7X0336 BOLT Caterpillar parts
215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235, 235C, 235D, 245, 245B, 3114, 3116, 3126, 5110B, 578, 583R, 587R, 587T, 621B, 631C, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G...
Rating:
Alternative (cross code) number:
CA7X0336
7X-0336
7X0336
CA7X0336
7X-0336
7X0336
Weight: 0.34 pounds 0 kg.
Information:
GRIP LENGTH
107.95
mm
HEAD HEIGHT
9.8
mm
HEX SIZE
19.05
mm
LENGTH
139.7
mm
MATERIAL
Steel 1035 MPa Min Tensile Strength Rc 33-39
THREAD SIZE
.50-13
COATING/PLATING
Zinc-Dichromate Coating
ASPHALT PAVER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$8.65
18 Feb 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar HEX Cap Screw 7X0336 New
$9.01
05 May 2022
0.3968[0.18] Pounds
US: ProperBuy
CTP Caterpillar Hex Head Bolts Zinc Plated (7x0336) Aftermarket
CTP
CTP
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 7X0336:
Information:
Remove And Install Connecting Rod Bearings
start by:a) remove oil pump1. Check the identification on the connecting rods and caps as to their location in the engine. The caps must be installed in original positions in the engine.2. Turn the crankshaft until two of the pistons are at bottom center. 3. Remove connecting rod caps (1) from the connecting rods. Remove the lower half of the bearings from the caps.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
4. Push the connecting rod away from the crankshaft and remove the upper half of the bearings from the connecting rods.5. Make sure the surface of the connecting rod where the bearings make contact is clean and free of dirt.
Make sure the tabs on the bearings are in alignment with the notches in the connecting rods and caps.
6. Install the upper half of new bearings in the connecting rods.7. Pull the connecting rod down slowly on the crankshaft.
Make sure the surfaces where the bearings make contact in the caps are clean and free of dirt.
8. Install new bearings (2) in the caps. Make sure the tabs on the bearings are in alignment with the notches in the caps.9. Put clean engine oil on the threads of the bolts in the connecting rods.10. Check the bearing clearance with Plastigage (A) as follows: a) Make sure the numbers on the caps and connecting rods are the same and are on the same respective side. If new connecting rods are installed, put the cylinder number on the rods and caps.b) Put the caps and plastigage (A) in the correct position on the connecting rods. Install the nuts that hold them.c) Tighten the two nuts evenly to a torque of 60 6 lb.ft. (81.3 8.1 N m). Put a mark on each nut and tighten the nuts 120° more from the marks. d) Remove the caps from the connecting rods and Plastigage (A). Measure the thickness of the Plastigage. The connecting rod bearing clearance must be .0028 to .0066 in. (0.071 to 0.168 mm) for new bearings.e) Put clean engine oil in the bearing caps and install them again. Follow the tightening procedure in Step 10.f) Do Steps 1 through 10 for the other connecting rod bearings.end by:a) install oil pump
start by:a) remove oil pump1. Check the identification on the connecting rods and caps as to their location in the engine. The caps must be installed in original positions in the engine.2. Turn the crankshaft until two of the pistons are at bottom center. 3. Remove connecting rod caps (1) from the connecting rods. Remove the lower half of the bearings from the caps.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
4. Push the connecting rod away from the crankshaft and remove the upper half of the bearings from the connecting rods.5. Make sure the surface of the connecting rod where the bearings make contact is clean and free of dirt.
Make sure the tabs on the bearings are in alignment with the notches in the connecting rods and caps.
6. Install the upper half of new bearings in the connecting rods.7. Pull the connecting rod down slowly on the crankshaft.
Make sure the surfaces where the bearings make contact in the caps are clean and free of dirt.
8. Install new bearings (2) in the caps. Make sure the tabs on the bearings are in alignment with the notches in the caps.9. Put clean engine oil on the threads of the bolts in the connecting rods.10. Check the bearing clearance with Plastigage (A) as follows: a) Make sure the numbers on the caps and connecting rods are the same and are on the same respective side. If new connecting rods are installed, put the cylinder number on the rods and caps.b) Put the caps and plastigage (A) in the correct position on the connecting rods. Install the nuts that hold them.c) Tighten the two nuts evenly to a torque of 60 6 lb.ft. (81.3 8.1 N m). Put a mark on each nut and tighten the nuts 120° more from the marks. d) Remove the caps from the connecting rods and Plastigage (A). Measure the thickness of the Plastigage. The connecting rod bearing clearance must be .0028 to .0066 in. (0.071 to 0.168 mm) for new bearings.e) Put clean engine oil in the bearing caps and install them again. Follow the tightening procedure in Step 10.f) Do Steps 1 through 10 for the other connecting rod bearings.end by:a) install oil pump
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
AD40, AD45, AE40, CS-323C
PM-565, PM-565B
5130, 5130B, D11N, D11R, D11T
5110B, D10, D10R
824G, 824G II, 844, 844H, 854G, 854K, CS-323, D10N, D10R, D11N, D11R
AD45, AE40 II
AE40 II, D10, D10N, D10R, D11N, D11R, D11T, D9G, D9N, D9R, D9T
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T
120K, 120K 2, 12K, 140K, 140K 2, 160K, 3116, 3126, 3126B, 3126E, 815B, C-9, C7, C9, SPP101
128, 129, 3116, 3126, 3126B, 3126E, 3406E, 515, 518C, 525, 528B, 530B, 966F, 966F II, C-15, C-16, C-18, C15, C7, D320A, D342, D353C, SG16, SG18
1190T, 1290T, 2491, 3116, 311B, 3126, 3126B, 3126E, 312B, 318B, 320B, 320B FM LL, 325 L, 325B, 330, 330 FM L, 330C L, 330D FM, 345C, 522B, 532, 551, 552, 552 2, 568 FM LL, 793D, 793F, 793F CMD, 793F O...
1584606
BOLT
3406B
3406B
7E3502
BOLT
3406B
3406B
120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14G, 160H, 160H ES, 160H NA, 163H NA, 16G, 3406B, 515, 525, 525B, 535B, 545, 621F, 623E, 623F, 627F, 631E...
3116, 3176, 3176B, 3176C, 3196, C-10, C-12, C-9, C11, C13, C9, CPT372, CX31-C13I
7E3477
BOLT
3176, 3176B
3176, 3176B
2470C, 3116, 3126, 314D CR, 314D LCR, 336E H, 336E LH, 553C, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 657E, 657G, 725, 730, 735, 735B, 740, 740B, 773F, 775F, 777C, 77...
3116, 3126, AP-900B, CS-531D, CS-533D, CS-563D, CS-573D, CS-583D
3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325 LN, 325B L, 325C, 325C FM, 539, C13, C7, CX28, M325B, M325C MH
140G, 3114, 3116, 3126, 3126B, 3126E, 525B, 525C, 535B, 535C, 545C, 793, 793B, 793C, 797, 797B, 815B, 910E, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928F, 928G, 950F, 950F II, 993K, C7, IT12B, IT18...