7X2542 BOLT Caterpillar parts
2384C, 2484C, 3126B, 3508, 3508B, 3512, 3512B, 3516, 3516B, 559C, 579C, 584, 844H, 854K, 906H, 906H2, 907H, 907H2, 908H, 908H2, 990H, 992K, 993K, C27, C32, CB-544, CB-545, CX31, D250E II, D300E II
Rating:
Alternative (cross code) number:
CA7X2542
7X-2542
7X2542
CA7X2542
7X-2542
7X2542
Weight: 0.13 pounds 0 kg.
Information:
COATING/PLATING
Zinc-Dichromate Coating
GRIP LENGTH
122
mm
HEAD HEIGHT
5.5
mm
HEX SIZE
13
mm
LENGTH
150
mm
MATERIAL
Steel - 1040 MPa Min Tensile Strength
THREAD SIZE
M8X1.25
ARTICULATED TRUCK, WHEEL LOADER,
Number on catalog scheme:
26
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00759331
Loosen the adjustment screws on valve bridges (4) .
Apply clean engine oil on the dowels for valve bridges (4) . Apply clean engine oil on the inside diameter of the valve bridges (4) . Apply clean engine oil on the top buffer of the valve bridges (4) .
Install valve bridges (4) on the dowels.
While valve bridges (4) are pushed straight down with a force of 5 to 45 N (1 to 10 lb), turn the adjustment screw until the screw contacts the valve stem. Turn the adjustment screw for an additional 20 degrees or 30 degrees. This will align the valve bridge straight on the dowel. This also compensates for the slack in the threads of the adjustment screw.
Hold the adjustment screw in position and tighten the nut on the adjustment screw to a torque of 30 4 N m (22 3 lb ft).
Apply Tooling (A) to the ends of pushrods (4) .
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
Illustration 2 g00759287
Install pushrods (3) in the valve lifters.
Install rocker shaft (2) on the valve cover base. Ensure that the rocker arms and the pushrods are aligned.
Install bolts (1) . Tighten the bolts to a torque of 109 14 N m (80 10 lb ft).
Set the valve lash on the intake valve to a clearance of 0.51 mm (0.020 inch). Set the valve lash on the exhaust valve to a clearance of 1.27 mm (0.050 inch).
Refer to the Testing and Adjusting Module, "Valve Lash and Valve Bridge Adjustment" for more information.End By: Install the valve cover and the spark plug. Refer to Disassembly and Assembly, "Valve Cover and Spark Plug - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00759331
Loosen the adjustment screws on valve bridges (4) .
Apply clean engine oil on the dowels for valve bridges (4) . Apply clean engine oil on the inside diameter of the valve bridges (4) . Apply clean engine oil on the top buffer of the valve bridges (4) .
Install valve bridges (4) on the dowels.
While valve bridges (4) are pushed straight down with a force of 5 to 45 N (1 to 10 lb), turn the adjustment screw until the screw contacts the valve stem. Turn the adjustment screw for an additional 20 degrees or 30 degrees. This will align the valve bridge straight on the dowel. This also compensates for the slack in the threads of the adjustment screw.
Hold the adjustment screw in position and tighten the nut on the adjustment screw to a torque of 30 4 N m (22 3 lb ft).
Apply Tooling (A) to the ends of pushrods (4) .
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
Illustration 2 g00759287
Install pushrods (3) in the valve lifters.
Install rocker shaft (2) on the valve cover base. Ensure that the rocker arms and the pushrods are aligned.
Install bolts (1) . Tighten the bolts to a torque of 109 14 N m (80 10 lb ft).
Set the valve lash on the intake valve to a clearance of 0.51 mm (0.020 inch). Set the valve lash on the exhaust valve to a clearance of 1.27 mm (0.050 inch).
Refer to the Testing and Adjusting Module, "Valve Lash and Valve Bridge Adjustment" for more information.End By: Install the valve cover and the spark plug. Refer to Disassembly and Assembly, "Valve Cover and Spark Plug - Remove and Install".
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
5110B, 5130, 5130B, 5230, 5230B, 795F AC, 795F XQ, 797, 797B, 797F, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 938G, ...
844, 844H, 844K, 854G, 854K, 950 GC, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, 990, 990 II, 990H, 990K, 992G, 992K, IT28G
365B II, 365B L, 365C, 374D L, 375 L, 385B, 385C, 385C L, 390D, 390D L, 844, 844H, 844K, 854G, 854K, 950H, 962H, 966H, 966K, 966M, 966M XE, 972H, 990, 990 II, 990H, 990K, 992G, 992K, AD55, CS-531C, CS...
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H, AP-1055B, AP-655C, AP-655D, AP1055E, AP555E...
854G, 854K, 988B, 988F, 988F II, 992G, 992K, R1600, R1600G, R1600H
120M, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 844, 844H, 844K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 986H, 990, 990 II, 990H, 990K, PM-465
390D, 390D L, 390F L, 5110B, 980G II, 980H, 980K, 988G, 988H, 988K, 990, 990 II, 990H, 990K, 992D, 992G, 992K, 993K
854G, 854K, 992G, 992K
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
795F AC, 795F XQ, 797, 797B, 797F, 988K, 990 II, 990H, 990K, 992K, 994F, 994H, R2900G, R3000H
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 3...
2384C, 2484C, 322 FM L, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 330, 330 FM L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336E L, 345B, 345B II, 345B I...
3383729
BOLT-FLANGE HEAD
3126B, C7, C9
3126B, C7, C9
3126B, 735B, 740B, 950H, 950K, 962H, 966K, 972K, C7, D6T LGP, D6T LGPPAT, D8T
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 30/30, 3116, 3126, 3126B, 3126E, 345C, 345C L, 345C MH, 345D, 345D L, 345D L V...
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
120H, 120K, 120K 2, 12K, 12M, 135H, 140G, 140K, 140K 2, 140M, 160K, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325...
3512B, 3516B, 3516C, 631C, 633C, 637D, 641, 793C, 797, 910, 916, 931B, 936F, D11N, D11R, D11T, D9T, IT18, IT18B, PM3516
1960404
BOLT
3054, 3056
3054, 3056
1947221
BOLT
3056, C6.6
3056, C6.6
1960335
BOLT
3034, 3054B, 3056
3034, 3054B, 3056
1272699
BOLT
3054, 3056, 312, 315, 317, 914G, IT14G, M312, M315, PS-150B, PS-200B, PS-300B
3054, 3056, 312, 315, 317, 914G, IT14G, M312, M315, PS-150B, PS-200B, PS-300B
1960336
BOLT
3054B, 3056
3054B, 3056
1954706
BOLT
3056
3056