BOLT 8T6430 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components. Use fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Aftercooler Core - Clean/Test
Aftercooler Core - Inspect
Battery - Recycle
Battery - Replace
Battery or Battery Cable - Disconnect
Coolant - Change
Coolant Extender (ELC) - Add
Engine - Clean
Engine Oil Level Gauge - Calibrate
Engine Storage Procedure - Check
Fuel System - Prime
Generator - Dry
Generator Bearing - Lubricate
Generator Set - Test
Generator Set Alignment - Check
Generator Winding - Test
Heat Exchanger - Clean/Test
Heat Exchanger - Inspect
Maintenance Recommendations
Rotating Rectifier - Check
Sea Water Strainer - Clean/Inspect
Varistor - Inspect
Daily
Coolant Level - Check
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Generator Bearing Temperature - Test/Record
Generator Load - Check
Power Factor - Check
Walk-Around Inspection
Every 8000 Service Hours
Rotating Rectifier - Check
Every Week
Generator - Inspect
Generator Set Vibration - Inspect
Standby Generator Set Maintenance Recommendations
Stator Winding Temperature - Test
Voltage and Frequency - Check
Every 50 Service Hours or Weekly
Aftercooler Condensate Drain Valve - Inspect/Clean
Engine Cooling System Corrosion Protection System - Inspect
Sea Water Strainer - Clean/Inspect
Overhaul
Aftercooler Core - Clean/Test
Generator Bearing - Inspect/Replace
Heat Exchanger - Clean/Test
Maintenance Recommendations
Overhaul (Major)
Overhaul (Top End)
Aftercooler Core - Inspect
Heat Exchanger - Inspect
Maintenance Recommendations
Oil Cooler Core - Check/Clean/Test
Overhaul (Top End)
Every 250 Service Hours
Battery Charger - Check
Battery Electrolyte Level - Check
Belts - Inspect/Adjust/Replace
Coolant Sample (Level 1) - Obtain
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Oil Sample - Obtain
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Coolant Sample (Level 2) - Obtain
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Fuel Injector - Check
Every 500 Service Hours
Engine Crankcase Breather - Clean
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Initial 1000 Service Hours
Aftercooler Core - Inspect
Heat Exchanger - Inspect
Every 1000 Service Hours
Engine Air Cleaner Element (Single Element) - Inspect/Replace
Generator Winding Insulation - Test
Turbocharger - Inspect
Every 2000 Service Hours
Fumes Disposal Filter Element - Replace
Stator Lead - Check
Every Year
Coolant Sample (Level 2) - Obtain
Varistor - Check
Every 3000 Service Hours
Auxiliary Water Pump (Bronze Impeller) - Inspect/Replace
Bolts (Fuel Filter Base) - Inspect/Replace
Coolant Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine Mounts - Inspect
Engine Speed/Timing Sensor - Clean/Inspect
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Fuel Injector - Check
Starting Motor - Inspect
Every 5000 Service Hours
Water Pump - Inspect