8T7058 BOLT-SOCKET HEAD Caterpillar parts
16M, 318C, 5130, 5130B, 572R, 572R II, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 730C, 844, 844K, 854G, 854K, 950G, 962G, 990, 990 II, 990K, 992G, 992K, C11, C13, CX31-C13I, E110B, E120B...
Rating:
Alternative (cross code) number:
CA8T7058
8T-7058
8T7058
CA8T7058
8T-7058
8T7058
Weight: 0.30 pounds 0 kg.
Information:
DR TYPE
HEX
GRIP LENGTH
104
mm
HEAD DIAMETER
18
mm
HEAD HEIGHT
12
mm
HEAD STYLE
SHD
LENGTH
140
mm
MATERIAL
Steel RC 35 Min
SOCKET SIZE
10
mm
THREAD SIZE
M12X1.75
ARTICULATED TRUCK, WHEEL TRACTOR-SCRAPER,
Number on catalog scheme:
4
For full view, you need register
Information:
Inspect the belts when the engine is stopped.Inspect the condition and the adjustment of the alternator belt and the accessory drive belt. Examine the belts for wear. Replace the belts if the belts show any signs of wear. Loose or worn pulley grooves cause belt slippage and low accessory drive speed. If belts are too loose, the belts vibrate enough to cause unnecessary wear on the belts and pulleys and possibly slip enough to cause overheating.If belts are too tight, unnecessary stresses are placed upon the pulley bearings and on the belts which might shorten the service life of both.If one belt in a set requires replacement, always install a new matched set of belts. Never replace just the worn belt. If only the worn belt is replaced, the new belt will carry all the load, as it will not be stretched as much as the older belts. All the belts will fail in rapid succession.
Belt tensioner.* If the engine is equipped with a freon compressor (air conditioner), the belt for the fan drive, the alternator, and the accessories will have an automatic belt tensioner.* If the engine is NOT equipped with a freon compressor, the alternator is used to adjust the belt tension.Remove the belt guard. Inspect the condition and adjustment of alternator belts and accessory drive belts (if equipped).To check the belt tension, apply 110 Newton (25 lb) of force, perpendicular to the belt, midway between the pulleys. Measure the belt deflection. Correctly adjusted belts will deflect 9 to 15 mm (3/8to 5/8 inch).If the belt does not require replacement or adjustment, install the belt guard. If the belt requires adjustment or replacement, perform the following procedure to adjust the belt tension.Alternator Belt Adjustment
(1) Adjusting bolt. (2) Mounting bolt.1. Slightly loosen mounting bolts (2) and adjusting bolt (1).2. Move the pulley to adjust the belt tension.3. Tighten adjusting bolt (1). Tighten mounting bolts (2).4. Install the belt guard.If a new belt is installed, check the belt adjustment again after 30 minutes of engine operation at rated speed.Water Pump Belt Adjustment
Exploded view of a water pump belt drive assembly: (1) Mounting bolt. (2) Square hole. (3) Adjusting bolt.1. Slightly loosen mounting bolt (1) and adjusting bolt (3).2. Adjust the belt tension with a square drive in the square hole (2).3. Tighten adjusting bolt (3). Tighten mounting bolt (1).4. Install the belt guard.If a new belt is installed, check the belt adjustment again after 30 minutes of engine operation at rated speed.
Belt tensioner.* If the engine is equipped with a freon compressor (air conditioner), the belt for the fan drive, the alternator, and the accessories will have an automatic belt tensioner.* If the engine is NOT equipped with a freon compressor, the alternator is used to adjust the belt tension.Remove the belt guard. Inspect the condition and adjustment of alternator belts and accessory drive belts (if equipped).To check the belt tension, apply 110 Newton (25 lb) of force, perpendicular to the belt, midway between the pulleys. Measure the belt deflection. Correctly adjusted belts will deflect 9 to 15 mm (3/8to 5/8 inch).If the belt does not require replacement or adjustment, install the belt guard. If the belt requires adjustment or replacement, perform the following procedure to adjust the belt tension.Alternator Belt Adjustment
(1) Adjusting bolt. (2) Mounting bolt.1. Slightly loosen mounting bolts (2) and adjusting bolt (1).2. Move the pulley to adjust the belt tension.3. Tighten adjusting bolt (1). Tighten mounting bolts (2).4. Install the belt guard.If a new belt is installed, check the belt adjustment again after 30 minutes of engine operation at rated speed.Water Pump Belt Adjustment
Exploded view of a water pump belt drive assembly: (1) Mounting bolt. (2) Square hole. (3) Adjusting bolt.1. Slightly loosen mounting bolt (1) and adjusting bolt (3).2. Adjust the belt tension with a square drive in the square hole (2).3. Tighten adjusting bolt (3). Tighten mounting bolt (1).4. Install the belt guard.If a new belt is installed, check the belt adjustment again after 30 minutes of engine operation at rated speed.
Cat SIS web machinery list:
Parts bolt Caterpillar catalog:
730, 730C, 740, 740B, 793, 793B, 793C, 793D, 988G, 988H, D400E II, D8R, D8T, M320
120M, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 844, 844H, 844K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 986H, 990, 990 II, 990H, 990K, PM-465
120M, 12M, 14M, 16M, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 5080, 5090B, 5110B, 525B, 525C, 53...
390D, 390D L, 390F L, 5110B, 980G II, 980H, 980K, 988G, 988H, 988K, 990, 990 II, 990H, 990K, 992D, 992G, 992K, 993K
854G, 854K, 992G, 992K
320C FM, 320D, 320D FM, 320D FM RR, 320D L, 322C, 322C FM, 324D FM, 325C FM, 325D FM, 325D FM LL, 325D MH, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 365B...
795F AC, 795F XQ, 797, 797B, 797F, 988K, 990 II, 990H, 990K, 992K, 994F, 994H, R2900G, R3000H
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 3...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14G, 14H, 14H NA, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 16M, 24H, 24M, 785B, 785C, 789B, 789C, 793B, 79...
725, 725C, 730, 730C
5130, 5130B, D11N, D11R, D11T
824G, 824G II, 844, 844H, 854G, 854K, CS-323, D10N, D10R, D11N, D11R
12E, 24H, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 777C, 777D, 777F, 834B, 836, 844, 844H, 990, 990 II, 990H, 992C, 992D, C18, D10N, D10R, D10T, D9L
C15, TH35-C15T
584, 586C, C-9, C13, C15, C7, C9, TH31-E61, TH35-C13T, TH35-C15T
312, 3126B, 312B L, 315, 315B L, 317, 324D, 324D L, 324D LN, 325D L, 329D L, 336D L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH,...
24M, 583T, 770, 770G, 770G OEM, 772, 772G, 772G OEM, 793F, 793F CMD, 793F OEM, 793F-XQ, 980G, 980G II, 980H, AD30, C-9, C11, C13, C15, C9, C9.3, CX31-C13I, CX31-C15I, CX31-C9I, D6R, D6R II, D6R III, D...
318C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 L, 320E L, 320E LN, 320E LRR, 321B, 321C, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E ...
315C, 315D L, 5110B, 918F, C11, C13, IT18F
320C, 320C FM, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 5110B, C11, C13, E240C, EL240B, GSH15-60, GSH9, GSH9B, TH35-C13T
120H, 12H, 135H, 140H, 140K, 143H, 14H, 160H, 160K, 163H, 16H, 572R II, C-9, C11, C13, C15, C18, C7, C9, CX31-C13I, CX31-C15I, CX35-P800, D6R, D6R III, D6R STD, D7E, D7E LGP, D7R II, D7R XR, TH31-E61,...
140K, 160K, C-9, C11, C13, C15, C18, C7, C9, CX31-C13I, CX31-C15I, CX35-P800, TH31-E61, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T
14M, 980C, C11, C13, CX31-C13I, SAT223, SAT318T, SAT322, TH35-C11I, TH35-C13I