1323157 BONNET-OIL COOLER Caterpillar parts
3176C, 345B L
Rating:
Alternative (cross code) number:
CA1323157
132-3157
1323157
CA1323157
132-3157
1323157
Weight: 1 pounds 0 kg.
EXCAVATOR, INDUSTRIAL ENGINE,
Number on catalog scheme:
5
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1 Start By:
Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00456860
Remove cover (1) and the gasket.
Illustration 2 g00456923
Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
Note: If the original lifters are installed in the fuel injection pump housing, put identification marks on the lifters in order to identify the location in the housing.
Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order to remove snap ring (4) .
Illustration 5 g00456926
Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing in order to loosen washer (5). Remove washer (5) .
Illustration 6 g00456927
Remove camshaft (6) .
Illustration 7 g00456928
Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
Remove bearings (8) from the governor end of the fuel injection pump housing.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1 Start By:
Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00456860
Remove cover (1) and the gasket.
Illustration 2 g00456923
Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
Note: If the original lifters are installed in the fuel injection pump housing, put identification marks on the lifters in order to identify the location in the housing.
Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order to remove snap ring (4) .
Illustration 5 g00456926
Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing in order to loosen washer (5). Remove washer (5) .
Illustration 6 g00456927
Remove camshaft (6) .
Illustration 7 g00456928
Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
Remove bearings (8) from the governor end of the fuel injection pump housing.
Caterpillar parts catalog:
Parts bonnet Caterpillar catalog:
1484476
BONNET-SEAL
G3408, G3412, G3512, G3516
G3408, G3412, G3512, G3516
3406E, 651B, 657B, 824C, 824G, 824G II, 824H, 825G II, 825H, 826G II, 826H, 834G, 834H, 836G, 836H, 980G, 980G II, 980H, 986H, 988G, 988H, C-15, C-16, C15, R2900G, R3000H
3406E, 651B, 657B, 824C, 824G, 824G II, 824H, 825G II, 825H, 826G II, 826H, 980G, 980G II, 980H, C-15, R2900G, R3000H
1390170
BONNET-OIL COOLER
3406E, 735, 740, D350E II, D400E II
3406E, 735, 740, D350E II, D400E II
7C8996
BONNET-OIL COOLER
3406E, D350E, D400E, D40D
3406E, D350E, D400E, D40D
3659872
BONNET-OIL COOLER
725C, 966K, 972K, C9.3
725C, 966K, 972K, C9.3
3116135
BONNET
C18
C18
3116134
BONNET
C18
C18
1470192
BONNET
24M, 651B, 834G, 834H, 836G, 836H, 986H, 988G, 988H, C-15, C-16, C15
24M, 651B, 834G, 834H, 836G, 836H, 986H, 988G, 988H, C-15, C-16, C15
24M, 621G, 623G, 627G, 631G, 637G, 657E, 657G, 824C, 824G, 824G II, 824H, 825G II, 825H, 826G II, 826H, 834G, 834H, 836G, 836H, 980G, 980G II, 980H, 988G, 988H, C-15, C-16, D8R II