6N1165 BONNET-OIL COOLER Caterpillar parts
3306, 3306B, 571G, 572G, 587R, 611, 615, 615C, D6C, D7G, D7G2, R1300, R1300G
Rating:
Alternative (cross code) number:
CA6N1165
6N-1165
6N1165
CA6N1165
6N-1165
6N1165
Weight: 5 pounds 2 kg.
INDUSTRIAL ENGINE, WHEEL TRACTOR,
Compatible equipment models: 6N1165:
Number on catalog scheme:
15
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 5 inch 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01187381
Disconnect tube assemblies (1) and (6).
Remove brackets (2), (3), and (4) from flywheel housing (7).
Attach a suitable lifting device to the transmission oil cooler. Remove bracket (5).
Remove bolts (8) and install Tooling (B).
Illustration 2 g01187390
Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately 98 kg (216 lb).
Remove remaining bolts (8). Remove flywheel housing (7) and the gasket from the rear flywheel housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 5 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01187390
Install Tooling (B) in the cylinder block.
Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately 98 kg (216 lb).
Position the gasket and flywheel housing (7) on the rear flywheel housing. Install bolts (8).
Remove Tooling (B) and install remaining bolts (8).
Illustration 4 g01187414
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 10 N m (41 7 lb ft).
In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 9 N m (35 7 lb ft).
Illustration 5 g01187381
Connect tube assemblies (1) and (6).
Install brackets (2), (3), (4), and (5). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 5 inch 2 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01187381
Disconnect tube assemblies (1) and (6).
Remove brackets (2), (3), and (4) from flywheel housing (7).
Attach a suitable lifting device to the transmission oil cooler. Remove bracket (5).
Remove bolts (8) and install Tooling (B).
Illustration 2 g01187390
Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately 98 kg (216 lb).
Remove remaining bolts (8). Remove flywheel housing (7) and the gasket from the rear flywheel housing. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Stud
1/2 - 13 NC by 5 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01187390
Install Tooling (B) in the cylinder block.
Attach Tooling (A) and a suitable lifting device to flywheel housing (7). The weight of flywheel housing (7) is approximately 98 kg (216 lb).
Position the gasket and flywheel housing (7) on the rear flywheel housing. Install bolts (8).
Remove Tooling (B) and install remaining bolts (8).
Illustration 4 g01187414
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt 1 through Bolt 2 to a torque of 55 10 N m (41 7 lb ft).
In a numerical sequence, tighten Bolt 3 through Bolt 10 to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, tighten Bolt 11 through Bolt 36 to a torque of 47 9 N m (35 7 lb ft).
Illustration 5 g01187381
Connect tube assemblies (1) and (6).
Install brackets (2), (3), (4), and (5). End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar parts catalog:
Parts bonnet Caterpillar catalog:
1673C, 235C, 235D, 330, 330 FM L, 330 L, 3306, 3306B, 330B, 330B L, 350, 545, 973, 973C, W330B
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 215, 235C, 3204, 330, 330 L, 3304, 3304B, 3306, 3306B, 330B L, 3408, 3408C...
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 235B, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 545, 572R, 611, 615C, 627...
12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA, 3304, 3306, 518C, 528, 528B, 530B, 561D, 930R, 966C, 966D, 972G, D4E, D5B, D6C, D6H, D7F, D7G
16G, 16H NA, 3406B, 3406C, 3408B, 3408C, 3412, 3412C, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8...
1673, 1673B, 1676, 3304, 3306, 621R, 623, 941, 950, 955H, 966C, 980, D330A, D330B, D333A, D333B, D336, D4D, D5, D6C, D7F, D7G
12G, 130G, 1673C, 215, 225, 235, 3160, 3208, 3304, 3306, 518, 613B, 637D, 639D, 920, 941, 950, 955L, 977K, 980B, D4D, D5, D6C, D6D, D7F, D7G
2867167
BONNET
587R
587R
14E, 518, 561C, 920, 930, 941, 950, 951B, 955K, 955L, 966C, 977K, D4D, D5, D6C, D7F
5S6061
BONNET
14E, 561C, 951B, 955L, 977K, D4D, D6C
14E, 561C, 951B, 955L, 977K, D4D, D6C
5S6395
BONNET
966C, 977K, D6C, D7F
966C, 977K, D6C, D7F
2P2840
BONNET
14E, 561C, 951B, 955K, 955L, 977K, D4D, D5, D6C
14E, 561C, 951B, 955K, 955L, 977K, D4D, D5, D6C
3306, 3306B, 611, 615, 615C, D7G, D7G2, R1300, R1300G
12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA, 1673C, 3304, 3306, 3306B, 3306C, 518C, 528, 528B, 530B, 578, 583R, 621E, 621R, 627, 627B, 627E, 627F, 627G, 63...
3306, 3306B, 621E, 621R, 627B, 627E, 627F, D6C
1673C, 3304, 3304B, 3306, 3306B, 3306C, 350, D6C, G3304, G3304B, G3306, G3306B
1673C, 235C, 235D, 330, 330 FM L, 330 L, 3306, 3306B, 330B, 330B L, 350, 545, 973, 973C, W330B
3912409
BONNET GP-OIL COOLER
C18 I6
C18 I6
8L4502
BONNET
3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, C-15, C-16, C12, C15, C18, CX31-C15I, D342, D342C, D343, D353C, G3406, G3408, G3408B, G3412, G343, G353D, T...
3306, 3306B, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, C-15, C-16, C12, C15, C18, CX31-C15I, D342, D342C, D343, D353C, G3406, G3408, G3408B, G3412, G343, G353D, T...
7L0877
BONNET-HEAT EXCHANGER
3304, 3304B, 3306, 3306B, G3304, G3306
3304, 3304B, 3306, 3306B, G3304, G3306
7L0875
BONNET-HEAT EXCHANGER
3304, 3304B, 3306, 3306B, G3304, G3306
3304, 3304B, 3306, 3306B, G3304, G3306
7W8833
BONNET AS-EXCHANGER
3126, 3208, 3306
3126, 3208, 3306
2W0760
BONNET-EXPANSION TANK
3126, 3208, 3304, 3306, 3306B
3126, 3208, 3304, 3306, 3306B
140H, 143H, 160H, 160H ES, 160H NA, 163H NA, 3306, 3306B, 627B, 627E, 627F, 627G, 637D, 639D, 65, 65C, D250E, D250E II, D25C, D300B, D300E, D30C, D350C, D35C, D6C, D6D, D7G