2012907 BOOM & BEARING AS Caterpillar parts
318C
Rating:
Alternative (cross code) number:
CA2012907
201-2907
2012907
CA2012907
201-2907
2012907
Weight: 2574 pounds 1167 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$55,354.29
19 Aug 2022
US: Empire Rigging
Crosby CRN BLK 24''90T QN 385 (2012907)
MCKISSICK
MCKISSICK
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 2012907:
Information:
Flash Program The Grade/Slope Control (ECM) For H-Series Motor Graders
Perform the following procedure in order to flash program the ECM. The ECM is flashed in order to upgrade the software. The new software will allow the ECM to communicate with the AccuGrade System. The Caterpillar Electronic Technician (Cat ET) contains the program WinFlash. WinFlash is used in order to load software into the ECM. The following procedure is used in order to FLASH software into the ECM.
Procedure
Connect the 7X-1425 Data Link Cable between the 7X-1700 Communication Adapter and the Electronic Technician.
Connect the 139-4166 Data Link Cable between the 7X-1700 Communication Adapter and the diagnostic connector of the machine.
Use WinFlash in order to load the software. Refer to Table 2 for the part number of the software.
Table 1
Machines Software Part Number
Motor Graders ( H- Series) 305-7418 Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.Flash Program The AccuGrade Components
Refer to "Flash Procedure" in order to flash program the system components. The system components are flashed in order to upgrade the software. The new software will allow the system components to communicate with the ECM and each other. The Caterpillar Electronic Technician (ET) contains the program WinFlash. WinFlash is used in order to load software into the system components. The following procedure is used in order to FLASH software into the system components.
Do not stop the process. The ECM will be damaged and need to be replaced.
Flash Procedure
Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.
Connect the 7X-1425 Data Link Cable between the 7X-1700 Communication Adapter and the Electronic Technician.
Connect the 139-4166 Data Link Cable between the 7X-1700 Communication Adapter and the diagnostic connector of the machine.
Use WinFlash in order to load the software. Refer to Table 2 for the part number of the software. 297-0153
Table 2
Software Part Number Component Description
297-0154 Laser receiver Monitor Software Gp
297-0153 Electronic mast Machine Software Gp
Perform the following procedure in order to flash program the ECM. The ECM is flashed in order to upgrade the software. The new software will allow the ECM to communicate with the AccuGrade System. The Caterpillar Electronic Technician (Cat ET) contains the program WinFlash. WinFlash is used in order to load software into the ECM. The following procedure is used in order to FLASH software into the ECM.
Procedure
Connect the 7X-1425 Data Link Cable between the 7X-1700 Communication Adapter and the Electronic Technician.
Connect the 139-4166 Data Link Cable between the 7X-1700 Communication Adapter and the diagnostic connector of the machine.
Use WinFlash in order to load the software. Refer to Table 2 for the part number of the software.
Table 1
Machines Software Part Number
Motor Graders ( H- Series) 305-7418 Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.Flash Program The AccuGrade Components
Refer to "Flash Procedure" in order to flash program the system components. The system components are flashed in order to upgrade the software. The new software will allow the system components to communicate with the ECM and each other. The Caterpillar Electronic Technician (ET) contains the program WinFlash. WinFlash is used in order to load software into the system components. The following procedure is used in order to FLASH software into the system components.
Do not stop the process. The ECM will be damaged and need to be replaced.
Flash Procedure
Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.
Connect the 7X-1425 Data Link Cable between the 7X-1700 Communication Adapter and the Electronic Technician.
Connect the 139-4166 Data Link Cable between the 7X-1700 Communication Adapter and the diagnostic connector of the machine.
Use WinFlash in order to load the software. Refer to Table 2 for the part number of the software. 297-0153
Table 2
Software Part Number Component Description
297-0154 Laser receiver Monitor Software Gp
297-0153 Electronic mast Machine Software Gp
Caterpillar parts catalog:
Parts boom Caterpillar catalog:
2747118
BOOM & BEARING AS
308C, 308E SR
308C, 308E SR
2339370
BOOM & BEARING AS
318C, 319C
318C, 319C
2195331
BOOM & BEARING AS
318C, 319C
318C, 319C
2145753
BOOM & BEARING AS
318C, 319C
318C, 319C