AVSPARE.COM
parts catalog

BOOM GP 2444351 - Caterpillar


2444351 BOOM GP Caterpillar parts 324D, 324D L, 324D LN
Rating:
65
Alternative (cross code) number:
CA2444351
244-4351
2444351
Caterpillar 2444351 BOOM GP

Buy BOOM GP 2444351 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2444351:

EXCAVATOR  324D   324D L   324D LN   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g00675955
Connector receptacles (Deutsch) and connector plugs (Deutsch)
Illustration 2 g00665457
Harness routing and seal plugs
Test Step 1. Check the Locking of the DT Connector (Deutsch) and Check the Lock Ring of the HD Style Connector (Deutsch)
Ensure that the connector is properly locked. Also ensure that the two halves of the connector can not be pulled apart.
Verify that the latch tab of the connector is properly latched. Also verify that the latch tab of the connector returns to the locked position. Expected Result:The connector will securely lock. The connector and the locking mechanism are without cracks or breaks.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connector or replace the connector, as required.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Allen Head Screw on the Connector for the Electronic Control Module (ECM)
Ensure that the allen head screw is properly tightened. Be careful not to overtighten the screw and break the screw.
Do not exceed 2.25 N m (20 lb in) of torque on the allen head screw. Expected Result:The ECM connector is secure and the allen head screw is properly torqued.Results:
OK - Proceed to Test Step 3.
Not OK - Repair: Repair the connector or replace the connector, as required.Verify that the repair eliminates the problem.STOPTest Step 3. Perform a Pull Test on Each Wire Terminal Connection
Each terminal and each connector should easily withstand 45 N (10 lb) of pull and each wire should remain in the connector body. This test checks whether the wire was properly crimped in the terminal and whether the terminal was properly inserted into the connector.
The DT connectors use a green wedge to lock the terminals in place. Ensure that the green wedge is not missing and that the green wedge is installed properly on the DT connectors. Note: Terminals should always be crimped onto the wires by using a crimp tool. Do not solder terminals. Use the 1U-5804 Crimp Tool.Expected Result:Each terminal and each connector easily withstands 45 N (10 lb) of pull and each wire remains in the connector body.Results:
OK - Proceed to Test Step 4.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 4. Perform the "Wiggle Test" on the Caterpillar Electronic Technician (ET)
Select the "Wiggle Test" from the diagnostic tests on Cat ET.
Press the "OK" button after you adhere to the warning.
Choose the appropriate group of parameters to monitor.
Press the "Start" button. Wiggle the wiring harness in order to reproduce intermittent problems.
If an intermittent problem exists, the status will be highlighted and an audible beep will be heard. Expected Result:No intermittent problems were indicated during the "Wiggle Test".Results:
OK - Proceed to Test Step 5.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 5. Check Wires for Nicks or Abrasion in the Insulation
Carefully inspect each wire for signs of abrasion, nicks, or cuts. The following areas are locations that should be checked:
Exposed insulation
Points of rubbing wire against the engine
Points of rubbing wire against a sharp point
Check all of

Caterpillar parts catalog:

Caterpillar parts catalog
324D & 324D L Excavators CJX00001-UP (MACHINE) POWERED BY C7 Engine
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine
324D L Excavator T2D00001-UP (MACHINE) POWERED BY C-7 Engine
324D L Hydraulic Excavator JJG00001-UP (MACHINE) POWERED BY C-7 Engine
324D L Excavator LAB00001-UP (MACHINE) POWERED BY C7 Engine
324D & 324D L Excavators JZR00001-UP (MACHINE) POWERED BY C7 Engine
324D & 324D L Excavators JAT00001-UP (MACHINE) POWERED BY C7 Engine
324D L Excavator PYT00001-UP (MACHINE) POWERED BY C7 Engine
324D L Excavator GPK00001-UP (MACHINE) POWERED BY C7 Engine


Parts boom Caterpillar catalog:

2481951 BOOM & BEARING AS
324D, 324D L, 324D LN
2602337 BOOM & BEARING AS
324D, 324D FM, 324D L, 326D L
2909234 BOOM & BEARING AS
324D, 324D L, 324D LN
2909240 BOOM & BEARING AS
324D, 324D L, 324D LN, 326D L
2941490 BOOM & BEARING AS
324D, 324D L, 324D LN
2368387 BOOM & BEARING AS
324D, 330D, 330D FM, 330D L, 330D LN, 336D, 340D L
2291907 BOOM AR-1 PIECE LONG
330D, 330D L, 336D, 340D L
2999538 BOOM AR-MASS
325D FM, 325D L, 329D L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.