3164844 BOOM AS Caterpillar parts
416E, 416F, 422E, 428E
Rating:
Alternative (cross code) number:
CA3164844
316-4844
3164844
CA3164844
316-4844
3164844
Weight: 734 pounds 332 kg.
BACKHOE LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$59.87
15 Sep 2019
-: -
Genuine Cummins 3164844 PLUG
Genuine Cummins 3164844 PLUG || Factory Direct Shipped Genuine OE Item || Availabilty is subject to change without notice || If needed immediately, please contact us for availability before purchasing
Genuine Cummins 3164844 PLUG || Factory Direct Shipped Genuine OE Item || Availabilty is subject to change without notice || If needed immediately, please contact us for availability before purchasing
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods are seated in the valve lifters.
Install rocker shaft assembly (1) in position on the cylinder head.
Ensure that the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the rocker shaft support.
Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the rocker shaft assembly.
Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
Tighten all the bolts in the numerical sequence to a torque of 155 N m (115 lb ft).
Tighten all the bolts in the numerical sequence to a torque of 250 17 N m (185 13 lb ft).
Tighten all the bolts again in the numerical sequence to a final torque of 250 17 N m (185 13 lb ft).
The assembled length of the springs at both ends of the rocker shaft must be 1.50 0.25 mm (.059 .010 inch). Remove the washers or install the washers behind the springs to change the assembled length of the springs.
Adjust the inlet valve lash to 0.38 0.08 mm (.015 .003 inch) and adjust the exhaust valve lash to 0.64 0.08 mm (.025 .003 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the adjusting screws (3) to a torque of 29 7 N m (21 5 lb ft). Refer to Specifications, "Valve Rocker Arms and Lifters".End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods are seated in the valve lifters.
Install rocker shaft assembly (1) in position on the cylinder head.
Ensure that the dowels on each end of the rocker shaft assembly are in alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the rocker shaft support.
Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the rocker shaft assembly.
Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
Tighten all the bolts in the numerical sequence to a torque of 155 N m (115 lb ft).
Tighten all the bolts in the numerical sequence to a torque of 250 17 N m (185 13 lb ft).
Tighten all the bolts again in the numerical sequence to a final torque of 250 17 N m (185 13 lb ft).
The assembled length of the springs at both ends of the rocker shaft must be 1.50 0.25 mm (.059 .010 inch). Remove the washers or install the washers behind the springs to change the assembled length of the springs.
Adjust the inlet valve lash to 0.38 0.08 mm (.015 .003 inch) and adjust the exhaust valve lash to 0.64 0.08 mm (.025 .003 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the adjusting screws (3) to a torque of 29 7 N m (21 5 lb ft). Refer to Specifications, "Valve Rocker Arms and Lifters".End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Caterpillar parts catalog:
Parts boom Caterpillar catalog:
3805776
BOOM GP
416E
416E
2099928
BOOM GP
416E, 416F, 422E, 428E
416E, 416F, 422E, 428E
3707055
BOOM AS
416E
416E
2196697
BOOM AS
TH580B
TH580B
2093068
BOOM AS
TH460B
TH460B
2023149
BOOM AS
TH460B, TH560B
TH460B, TH560B
2104812
BOOM AS
TH340B
TH340B
2104806
BOOM AS
TH340B
TH340B
2104799
BOOM AS
TH340B
TH340B
2419372
BOOM AS
446D
446D
2378086
BOOM AS
446D
446D
3057313
BOOM AS
442E, 444E
442E, 444E
3172486
BOOM AS
430E, 430F
430E, 430F
3707055
BOOM AS
416E
416E
3160040
BOOM AS
420E, 420F, 432E, 434E
420E, 420F, 432E, 434E