4Y2581 BOOT ASSEM. Caterpillar parts
966D
Rating:
Alternative (cross code) number:
CA4Y2581
4Y-2581
4Y2581
CA4Y2581
4Y-2581
4Y2581
Weight: 0.04 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 4Y2581:
Information:
The correct air/fuel ratio is very important for the following considerations:
Margin of detonation
Control of emissions
Achieving optimum service life for the engineIf the air/fuel ratio is not appropriate for the fuel and the operating conditions, a failure of the engine may occur. The service life of the turbocharger, the valves, and other components may be reduced.Fuel Supply Pressure
Make sure that the pressure of the gas to the gas pressure regulator is sufficient.For low pressure gas, pressure of 10 to 35 kPa (1.5 to 5.0 psi) is required for the gas pressure regulator.For high pressure gas, pressure of 83 to 172 kPa (12 to 25 psi) is required for the gas pressure regulator.
Use only properly designated Caterpillar gas pressure regulators.
Fluctuations of the fuel pressure can change the air/fuel ratio. For low pressure gas fuel systems, the maximum fluctuation that is allowed in the fuel pressure to the engine is 1.7 kPa ( 0.25 psi).Gas Pressure Regulator
The gas pressure regulator maintains a pressure differential between the air and the fuel that is supplied to the carburetor. After setting, the gas pressure regulator will maintain the pressure differential in response to changes in the air pressure.Determine whether the pressure regulator uses positive pressure or negative pressure.For engines with dual fuel systems, both of the regulators must be adjusted.A water manometer is used to measure the pressure differential. This measurement is taken when the engine is operating at high idle rpm. When a load is applied, the fuel pressure will usually decrease by approximately 0.25 to 0.5 kPa (1 to 2 inches of H2O). If the performance of the gas pressure regulator is erratic, the gas pressure regulator may require service.Installation Before the Gas Pressure Regulator
To prevent particles from entering the engine, install a one micron fuel filter 1 m (3 ft) before the gas pressure regulator. The recommended filter is the 4P-4717 Fuel Filter with the 4P-4720 Gas Filter Element.Adjusting the Gas Pressure to the Engine
Table 1
Tools Needed Qty
8T-5160 Gas Regulator Setting Tool 1 Adjusting the Positive Pressure Regulator
Make sure that the gas to the gas pressure regulator is shut OFF. Note: A water manometer may be used instead of the 1U-5470 Engine Pressure Group.
Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group.
Illustration 1 g00777970
Typical arrangement for low pressure gas
(1) Plug in the gas line to the carburetor
(2) Air filter service indicator on the air cleaner
(3) Cap
For low pressure gas, remove plug (1). Remove service indicator (2) from the air cleaner. Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group into the openings.
Illustration 2 g00822704
Typical arrangement for high pressure gas
(1) Plug in the gas line to the carburetor
(2) Plug in the balance line from the aftercooler
(3) Cap
For high pressure gas, remove plugs (1) and (2). Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group into the openings.
Remove cap (3). The nut for adjusting the gas pressure regulator is under the cap.
Turn ON
Margin of detonation
Control of emissions
Achieving optimum service life for the engineIf the air/fuel ratio is not appropriate for the fuel and the operating conditions, a failure of the engine may occur. The service life of the turbocharger, the valves, and other components may be reduced.Fuel Supply Pressure
Make sure that the pressure of the gas to the gas pressure regulator is sufficient.For low pressure gas, pressure of 10 to 35 kPa (1.5 to 5.0 psi) is required for the gas pressure regulator.For high pressure gas, pressure of 83 to 172 kPa (12 to 25 psi) is required for the gas pressure regulator.
Use only properly designated Caterpillar gas pressure regulators.
Fluctuations of the fuel pressure can change the air/fuel ratio. For low pressure gas fuel systems, the maximum fluctuation that is allowed in the fuel pressure to the engine is 1.7 kPa ( 0.25 psi).Gas Pressure Regulator
The gas pressure regulator maintains a pressure differential between the air and the fuel that is supplied to the carburetor. After setting, the gas pressure regulator will maintain the pressure differential in response to changes in the air pressure.Determine whether the pressure regulator uses positive pressure or negative pressure.For engines with dual fuel systems, both of the regulators must be adjusted.A water manometer is used to measure the pressure differential. This measurement is taken when the engine is operating at high idle rpm. When a load is applied, the fuel pressure will usually decrease by approximately 0.25 to 0.5 kPa (1 to 2 inches of H2O). If the performance of the gas pressure regulator is erratic, the gas pressure regulator may require service.Installation Before the Gas Pressure Regulator
To prevent particles from entering the engine, install a one micron fuel filter 1 m (3 ft) before the gas pressure regulator. The recommended filter is the 4P-4717 Fuel Filter with the 4P-4720 Gas Filter Element.Adjusting the Gas Pressure to the Engine
Table 1
Tools Needed Qty
8T-5160 Gas Regulator Setting Tool 1 Adjusting the Positive Pressure Regulator
Make sure that the gas to the gas pressure regulator is shut OFF. Note: A water manometer may be used instead of the 1U-5470 Engine Pressure Group.
Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group.
Illustration 1 g00777970
Typical arrangement for low pressure gas
(1) Plug in the gas line to the carburetor
(2) Air filter service indicator on the air cleaner
(3) Cap
For low pressure gas, remove plug (1). Remove service indicator (2) from the air cleaner. Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group into the openings.
Illustration 2 g00822704
Typical arrangement for high pressure gas
(1) Plug in the gas line to the carburetor
(2) Plug in the balance line from the aftercooler
(3) Cap
For high pressure gas, remove plugs (1) and (2). Attach the lines for the differential pressure gauge of the 1U-5470 Engine Pressure Group into the openings.
Remove cap (3). The nut for adjusting the gas pressure regulator is under the cap.
Turn ON
Caterpillar parts catalog:
Parts boot Caterpillar catalog:
4M1829
BOOT-RUBBER
1090, 1140, 1150, 1160, 1190, 1190T, 1290T, 12E, 130G, 140G, 16, 1673, 1673B, 1673C, 1676, 1693, 16G, 215, 225, 235, 235D, 245, 24H, 3176C, 3196, 3204, 3208, 330 L, 3304, 3306, 3306B, 330D L, 3406, 34...
1090, 1140, 1150, 1160, 1190, 1190T, 1290T, 12E, 130G, 140G, 16, 1673, 1673B, 1673C, 1676, 1693, 16G, 215, 225, 235, 235D, 245, 24H, 3176C, 3196, 3204, 3208, 330 L, 3304, 3306, 3306B, 330D L, 3406, 34...
3V0582
BOOT
814B, 815B, 816B, 824C, 826C, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, 980F II, CS-643, D5B, G936, IT28, IT28B
814B, 815B, 816B, 824C, 826C, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, 980F II, CS-643, D5B, G936, IT28, IT28B
5D3636
BOOT
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
9G9508
BOOT
916, 926, 936, 936F, 950B, 966D, 980C, 988B, 992C, 994, 994D, D8L, G936, IT28, IT28B
916, 926, 936, 936F, 950B, 966D, 980C, 988B, 992C, 994, 994D, D8L, G936, IT28, IT28B
6E0747
BOOT
950B, 950F, 966D, 966F, 980C
950B, 950F, 966D, 966F, 980C
3Y9739
BOOT ASSEM.
966D
966D
3Y9739
BOOT ASSEM.
966D
966D
3Y1111
BOOT
950
950
1228201
BOOT ASSEM.
966F
966F
9K1019
BOOT
518, 528, 528B, 530B, 992
518, 528, 528B, 530B, 992
5K7167
BOOT
950
950
3K2100
BOOT
950
950
7U5783
BOOT
D250D, D250E, D25D, D300D, D300E, D350E, D400E, D40D
D250D, D250E, D25D, D300D, D300E, D350E, D400E, D40D
3U4577
BOOT-THROTTLE PEDAL
D250B, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
D250B, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
1285082
BOOT
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 16H NA, 69D, 725, 730, 735, 740, 769D, 771D, 773D, 77...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 16H NA, 69D, 725, 730, 735, 740, 769D, 771D, 773D, 77...
2A7236
BOOT
776C
776C
7N4088
BOOT
776C, 777D, 784C, 785, 785B, 785C
776C, 777D, 784C, 785, 785B, 785C
8X2959
BOOT
784B, 785, 785B, 789B, 793B, 793C
784B, 785, 785B, 789B, 793B, 793C