1219134 BOTTOM GUARD Caterpillar parts
307B
Rating:
Alternative (cross code) number:
CA1219134
121-9134
1219134
CA1219134
121-9134
1219134
MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$4.50
24 Jan 2020
-: -
Tennant OEM 1219134
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 1219134:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g00755773
Remove four bolts (1) and floor panel (2) from the machine. The weight of the floor panel is approximately 20 kg (45 lb).
Illustration 2 g00755774
Disconnect three wires (4) from the three solenoids.
Disconnect eight connectors (3) from the eight solenoids. Disconnect three ground wires (5). Move the wiring harness out of the way.
Illustration 3 g00755775
Disconnect ten hose assemblies (6) from the control valve. Remove the O-ring seals from the hose assemblies.
Illustration 4 g00755776
Disconnect eight hose assemblies (8). Remove the O-ring seals from the eight hose assemblies.
Remove three hose assemblies (7). Remove the O-ring seals from the three hose assemblies.
Illustration 5 g00755806
Use Tooling (A), chains and a suitable lifting device in order to support control valve (9).
Illustration 6 g00755818
Remove nuts (10) and the washers. The nuts are located under the control valve.
Remove the control valve. The weight of the control valve is approximately 84 kg (185 lb).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g00755773
Remove four bolts (1) and floor panel (2) from the machine. The weight of the floor panel is approximately 20 kg (45 lb).
Illustration 2 g00755774
Disconnect three wires (4) from the three solenoids.
Disconnect eight connectors (3) from the eight solenoids. Disconnect three ground wires (5). Move the wiring harness out of the way.
Illustration 3 g00755775
Disconnect ten hose assemblies (6) from the control valve. Remove the O-ring seals from the hose assemblies.
Illustration 4 g00755776
Disconnect eight hose assemblies (8). Remove the O-ring seals from the eight hose assemblies.
Remove three hose assemblies (7). Remove the O-ring seals from the three hose assemblies.
Illustration 5 g00755806
Use Tooling (A), chains and a suitable lifting device in order to support control valve (9).
Illustration 6 g00755818
Remove nuts (10) and the washers. The nuts are located under the control valve.
Remove the control valve. The weight of the control valve is approximately 84 kg (185 lb).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts bottom Caterpillar catalog:
311B, 312B
1449307
BOTTOM GUARD
311B, 312B
311B, 312B
1351376
BOTTOM GUARD
311B, 312B
311B, 312B
1168389
BOTTOM GUARD
311B, 312B
311B, 312B
1011631
BOTTOM-TANK
3176B, 3176C, 3196, C-12, C12
3176B, 3176C, 3196, C-12, C12
0898257
BOTTOM COVER
RT100
RT100
1420955
BOTTOM GUARD
307B
307B