AVSPARE.COM
parts catalog

BRACE, RADIATOR B139847 - Caterpillar



B139847 BRACE, RADIATOR Caterpillar parts CB-614 BRACE
Rating:
44
Alternative (cross code) number:
CAB139847
B13-9847
B139847
Caterpillar B139847 BRACE, RADIATOR

Buy BRACE, RADIATOR B139847 Caterpillar genuine, new aftermarket tractor parts with delivery
VIBRATORY COMPACTOR,

Compatible equipment models: B139847:

VIBRATORY COMPACTOR  CB-614   Caterpillar
Number on catalog scheme: 22
  
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tool    
Tool     Part Number     Part Description     Qty    
A     6V-4077     Camshaft Bearing Tool     1    
125-2739 (1) Bearing Pilot     1    
125-2740 (1) Back Up Plate     1    
125-2741 (1) Bearing Sleeve     1    
B     8S-2241     Camshaft Bearing Tool Group     1    
C     5P-5247     Hydraulic Puller     1    
D     8H-0684     Ratchet Wrench     1    
( 1 ) Alternate Tooling for camshaft bearings with a large diameter
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00578338
Install camshaft bearing (1) on Tooling (A) .Note: Tooling (B) can be used to install the camshaft bearings when the flywheel housing and the front housing have been removed.
Position camshaft bearing (1) and Tooling (A) in the bore.Note: The joint in camshaft bearing (1) must be on the horizontal centerline of the bore. The upper oil hole must be 20 5 degrees above the horizontal centerline of the bore. The lower oil hole of camshaft bearing (1) should be 20 5 degrees below the horizontal centerline of the bore. The joints of camshaft bearing (1) on the right side of the engine must face the inside of the cylinder block. The joints of camshaft bearing (1) on the left side of the engine must face the outside of the cylinder block.
Illustration 2 g01208939
Install Tooling (C) on Tooling (A) and pull camshaft bearing (1) (not shown) into the bore.Note: Tooling (D) can be used in place of Tooling (C) .
After camshaft bearing (1) (not shown) is installed, measure the bore. The bore must be 92.00 0.06 mm (3.620 0.002 inch).End By: Install the camshafts. Refer to Disassembly and Assembly, "Camshaft - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
CB-614 VIBRATORY COMPACTOR 7CD00001-00115 (MACHINE)


Parts brace Caterpillar catalog:

1241703 BRACE
322C, 322C FM, 325C, 325C FM, 330B, 330B L, M325C MH, W330B
7Y1364 BRACE
322C, 322C FM, 325B, 325B L, 325C, 325C FM, 330, 330 FM L, 330 L, M325C MH
1189820 BRACE
322B, 322B L, 325B, 325B L, 330C, 330C FM, 330C L, 330C MH, M325B
1881715 BRACE AS
320B FM LL, 320C FM
1881716 BRACE AS
320B FM LL, 320C FM
12690060 BRACE
PS-130, PS-180
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.