1059324 BRACKET AS Caterpillar parts
320 L
Rating:
Alternative (cross code) number:
CA1059324
105-9324
1059324
CA1059324
105-9324
1059324
Weight: 2 pounds 1 kg.
EXCAVATOR,
Compatible equipment models: 1059324:
Number on catalog scheme:
5
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 9T-3665 Rod 2
6V-8149 Nut 2
5P-8245 Hard Washer 2
5F-7345 Screw 1
8B-7560 Step Plate 1 Note: Be sure that all of the parts of the traction control valve are thoroughly clean prior to assembly. If any parts are worn or damaged, use new parts for replacement. All assembly procedures must be performed on a clean work surface and in a clean area. During the assembly of the traction control valve, lubricate all of the parts with clean hydraulic oil. Note: O-rings, gaskets and seals should always be replaced. A used O-ring may not have the same sealing properties as a new O-ring. A reconditioning procedure should not be degraded because of a low cost component such as an O-ring or a gasket. Use 1U-6396 O-Ring Assembly Compound during the assembly procedure.
Make sure that all components of the traction control valve are thoroughly clean prior to assembly.
Illustration 1 g00641968
Install O-ring (29) and O-ring (28) .
Install O-ring (27) and two backup rings (26) .
Install O-ring (25) and two backup rings (24) .
Illustration 2 g00641964
Install two relief valves (23) in the valve body.
Illustration 3 g00641961
Install O-ring seal (22) on plug (20) .
Install drive (21), valve (17), sleeve (18), spring (19), and plug (20) in valve body (10) .
Illustration 4 g00641955
Install O-ring seal (13) on plug (12) .
Install stem (16), sleeve (15), spring (14) and plug (12) in valve body (10) .
Illustration 5 g00641947
Note: Prior to installation, thoroughly clean the outer surface of the spool assembly (11) .
Install spool assembly (11) in the valve body (10) .
Install seats (9), springs (8), and plungers (9) in the valve body.
Illustration 6 g00642477
Install two socket head bolts (5) in cover (6) .
Place cover (6) over plunger (7), and install Tooling (A), as shown. Make sure that cover (6) is square with the valve body by measuring dimension (X) on both sides of the cover.
Compress cover (6) with Tooling (A), while you keep dimension (X) equal on each side of the cover. Continue to compress until the cover makes contact with the valve body. Tighten two socket head bolts (5) .
Remove Tooling (A) from the traction control valve. Install the other two socket head bolts (5) .
Repeat Step 12 through Step 15 in order to install the opposite cover (6) .
Illustration 7 g00641883
Install O-ring (4) on each plug. Install two plugs (3) in the valve body.
Illustration 8 g00641885
Install two O-rings (2) and two O-rings (1) on the valve body.End By: Install the traction control valve. Refer to Disassembly and Assembly, "Traction Control Valve - Install" in this manual.
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 9T-3665 Rod 2
6V-8149 Nut 2
5P-8245 Hard Washer 2
5F-7345 Screw 1
8B-7560 Step Plate 1 Note: Be sure that all of the parts of the traction control valve are thoroughly clean prior to assembly. If any parts are worn or damaged, use new parts for replacement. All assembly procedures must be performed on a clean work surface and in a clean area. During the assembly of the traction control valve, lubricate all of the parts with clean hydraulic oil. Note: O-rings, gaskets and seals should always be replaced. A used O-ring may not have the same sealing properties as a new O-ring. A reconditioning procedure should not be degraded because of a low cost component such as an O-ring or a gasket. Use 1U-6396 O-Ring Assembly Compound during the assembly procedure.
Make sure that all components of the traction control valve are thoroughly clean prior to assembly.
Illustration 1 g00641968
Install O-ring (29) and O-ring (28) .
Install O-ring (27) and two backup rings (26) .
Install O-ring (25) and two backup rings (24) .
Illustration 2 g00641964
Install two relief valves (23) in the valve body.
Illustration 3 g00641961
Install O-ring seal (22) on plug (20) .
Install drive (21), valve (17), sleeve (18), spring (19), and plug (20) in valve body (10) .
Illustration 4 g00641955
Install O-ring seal (13) on plug (12) .
Install stem (16), sleeve (15), spring (14) and plug (12) in valve body (10) .
Illustration 5 g00641947
Note: Prior to installation, thoroughly clean the outer surface of the spool assembly (11) .
Install spool assembly (11) in the valve body (10) .
Install seats (9), springs (8), and plungers (9) in the valve body.
Illustration 6 g00642477
Install two socket head bolts (5) in cover (6) .
Place cover (6) over plunger (7), and install Tooling (A), as shown. Make sure that cover (6) is square with the valve body by measuring dimension (X) on both sides of the cover.
Compress cover (6) with Tooling (A), while you keep dimension (X) equal on each side of the cover. Continue to compress until the cover makes contact with the valve body. Tighten two socket head bolts (5) .
Remove Tooling (A) from the traction control valve. Install the other two socket head bolts (5) .
Repeat Step 12 through Step 15 in order to install the opposite cover (6) .
Illustration 7 g00641883
Install O-ring (4) on each plug. Install two plugs (3) in the valve body.
Illustration 8 g00641885
Install two O-rings (2) and two O-rings (1) on the valve body.End By: Install the traction control valve. Refer to Disassembly and Assembly, "Traction Control Valve - Install" in this manual.
Caterpillar parts catalog:
Parts bracket Caterpillar catalog:
4I3078
BRACKET-STOPPER
307, 307B, 311, 311B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 350, 365B, 365B L, 385B
307, 307B, 311, 311B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 350, 365B, 365B L, 385B
4I4224
BRACKET AS-CATCH
311, 311B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 350, 365B, 365B L, 385B
311, 311B, 315, 318B, 320 L, 320B, 320N, 322 FM L, 325, 325 L, 325 LN, 325B, 330, 330 FM L, 330 L, 345B II, 350, 365B, 365B L, 385B
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
7Y8234
BRACKET
307, 311, 315, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B
307, 311, 315, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B
7Y8233
BRACKET
307, 311, 315, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B
307, 311, 315, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B
6C6725
BRACKET
320 L, 320B, 322B LN, 325C, 325D L, 345C L, 350, 350 L, 375, 5080
320 L, 320B, 322B LN, 325C, 325D L, 345C L, 350, 350 L, 375, 5080
1123310
BRACKET
320 L, 320B, 320C, 322 LN, 322B LN, 322C, 323D L, 325B L, 325C, 325D, 325D L, 330C, 330C L, 330D L, 330D LN, 336D L
320 L, 320B, 320C, 322 LN, 322B LN, 322C, 323D L, 325B L, 325C, 325D, 325D L, 330C, 330C L, 330D L, 330D LN, 336D L
1169224
BRACKET AS
320 L
320 L
1125117
BRACKET AS
320 L, 322 FM L, 322 LN, 325, 325 FM L, 330, 330 L
320 L, 322 FM L, 322 LN, 325, 325 FM L, 330, 330 L
7Y1894
BRACKET
320 L
320 L
320 L, 320B L
0878661
BRACKET AS
320 L, E70B
320 L, E70B
1169224
BRACKET AS
320 L
320 L
4I5470
BRACKET AS
320 L
320 L
1060110
BRACKET AS
320 L, 320N
320 L, 320N
4I8355
BRACKET AS
320 L, 322, 322 FM L, 325, 325 L, 325 LN
320 L, 322, 322 FM L, 325, 325 L, 325 LN
6C9296
BRACKET-RH
330 L
330 L
1027888
BRACKET AS
320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 330, 330 FM L, 330 L
320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 330, 330 FM L, 330 L
1162029
BRACKET
322 FM L
322 FM L
1099304
BRACKET AS-FRONT
322, 322 LN
322, 322 LN
1099307
BRACKET AS-FRONT
322, 322 LN
322, 322 LN
1099302
BRACKET AS-REAR
322, 322 LN
322, 322 LN
6C6723
BRACKET AS
320 L
320 L
1125117
BRACKET AS
320 L, 322 FM L, 322 LN, 325, 325 FM L, 330, 330 L
320 L, 322 FM L, 322 LN, 325, 325 FM L, 330, 330 L