2161010 BRACKET Caterpillar parts
302.5C, 303
Rating:
Alternative (cross code) number:
CA2161010
216-1010
2161010
CA2161010
216-1010
2161010
Weight: 0.07 pounds 0 kg.
MINI HYD EXCAVATOR,
Number on catalog scheme:
12
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 311-1362 Vacuum Cap 1 Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Engage the parking brake.
Illustration 1 g01397769
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g01404275
Remove bolts (1). Repeat this step for the opposite side of the machine.
Remove cover (2) .
Illustration 3 g01404279
Disconnect tube assemblies (3) .
Disconnect hose assembly (5) .
Remove tube assembly (4) .
Illustration 4 g01404306
Remove tube assemblies (6), (7), (8), and (9) .
Illustration 5 g01404332
Remove bolts (10). Remove steering control valve (11) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 311-1362 Vacuum Cap 1 Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Engage the parking brake.
Illustration 1 g01397769
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g01404275
Remove bolts (1). Repeat this step for the opposite side of the machine.
Remove cover (2) .
Illustration 3 g01404279
Disconnect tube assemblies (3) .
Disconnect hose assembly (5) .
Remove tube assembly (4) .
Illustration 4 g01404306
Remove tube assemblies (6), (7), (8), and (9) .
Illustration 5 g01404332
Remove bolts (10). Remove steering control valve (11) .
Caterpillar parts catalog:
Parts bracket Caterpillar catalog:
1946401
BRACKET
303
303
2278561
BRACKET
303
303
2278560
BRACKET
303
303
2070185
BRACKET AS
315C
315C
1992336
BRACKET AS
302.5C, 303, 304
302.5C, 303, 304
1992366
BRACKET AS
302.5C, 303, 304, 305
302.5C, 303, 304, 305
1992361
BRACKET AS
302.5C, 303, 304, 305
302.5C, 303, 304, 305