BRACKET AS-YM 2888732 - Caterpillar

2888732 BRACKET AS-YM Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2888732
288-8732
2888732

Weight: 88 pounds 39 kg.

Buy BRACKET AS-YM 2888732 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:

8W1751 BRACKET AS-YM 2888732 CL

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

1 Pc of Bracket A, Compatible with Caterpillar 2888732 2G8786 8D5946 8D5769 2G8785

$985.58

05 Aug 2020

-: -

1 Pc of Bracket A, Compatible with Caterpillar 2888732 2G8786 8D5946 8D5769 2G8785
One New Aftermarket Replacement Bracket Assembly, Compatible With Caterpillar Motor Grader Models: 120G, 120H, 120H ES, 120H NA, 12G, 12H Note: Does Not Have 9D8285 Cap Replaces Part Numbers: 8W1751, IMM50-0014

Show more prices Caterpillar parts

For full view, you need register

Information:

Locomotive EngineC175-16 (S/N: 3A91-UP; Y3A1-UP; KWT1-UP; R1X1-UP)Off Highway Truck793F (S/N: SND1-UP; SSP1-UP; RBT1-UP)793F AC (S/N: EMD1-UP)794 AC (S/N: MN51-UP; MT51-UP)795F (S/N: SNT1-UP)795F AC (S/N: ERM1-UP)797F (S/N: LAJ1-UP; WSP1-UP)Introduction
The following Special Instruction covers the inspection and installation of 437-3038 Exhaust Log Bellows, 466-4983 Bellows As, 485-3800 Bellows As, and 443-5940 Turbine Inlet Bellows on C175 Engines.Do not perform any procedures listed in this Special Instruction until you have read and understood the information.Required Tooling
Table 1
Tooling
Part Number Description
463-4043 Compression Tool
452-6804 Compression Tool Pre-Installation Inspection
Illustration 1 g03701901
Inspect for a minimum of 2.5 mm (0.10 inch) ribbon of bellows material concentric around the flange.
Illustration 2 g03701966
(1) Measurement Locations
Illustration 3 g03703303
(2) Liner is Not Seated Properly
Measure four locations around the flange of the bellow (no more than 1 mm (0.040 inch) delta between measurements allowed) to verify correct liner seating. If the liner is not straight or if the liner is loose, the bellows should be discarded.Bellows Installation
Use only 437-3038 Log Bellows, 466-4983 Bellows As, 485-3800 Bellows As, 442-5766 V Band Clamps, and 467-4241 Band Clamp with 463-4043 Compression Tool.Use only 443-5940 Turbine Inlet Bellows and 446-1290 V Band Clamps with 452-6804 Compression Tool.
Illustration 4 g03360580
Illustration 5 g03360680
Illustration 6 g03703335
Incorrect Condition - Liners touching during compression. If this occurs, discard the bellows.
Illustration 7 g03703531
Use compression tools as mentioned above to compress bellows for install. If there is a popping noise during compression or if the liners contact each other, discard the bellow.
Illustration 8 g03703696
Install bellows onto the engine ensuring proper seating of shim rings under the clamps. Proper installation is critical to prevent premature bellows failure.
Illustration 9 g03703573
Incorrect Shim Ring and Clamp Installation.