2D6201 BRACKET Caterpillar parts
120, 120B, 12E, 12F, 140, 140B, 14E
Rating:
Alternative (cross code) number:
CA2D6201
2D-6201
2D6201
CA2D6201
2D-6201
2D6201
Weight: 18 pounds 8 kg.
MOTOR GRADER,
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Drain the secondary filters. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 1 g03389540
Typical example
Make temporary identification marks on all the plastic tube assemblies in order to show the correct position of the tube assemblies.
Place a suitable container below the fuel filter base in order to catch any fuel that might be spilled.
Disconnect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) from the fuel filter base.
Use Tooling (A) in order to plug the plastic tube assemblies. Use Tooling (A) in order to cap the ports in the fuel filter base.
Illustration 2 g03389546
Typical example
Remove secondary filters (6) from canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove bolts (4) from fuel filter base (5). Remove the fuel filter base from the mounting bracket. Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting , "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 3 g03389546
Typical example
Ensure that fuel filter base (5) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Position fuel filter base (5) on the mounting bracket. Install bolts (4). Tighten the bolts to a torque of 44 N m (32 lb ft).
If necessary, install new fuel filters (6) to canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 4 g03389540
Typical example
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies
Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Drain the secondary filters. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 1 g03389540
Typical example
Make temporary identification marks on all the plastic tube assemblies in order to show the correct position of the tube assemblies.
Place a suitable container below the fuel filter base in order to catch any fuel that might be spilled.
Disconnect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) from the fuel filter base.
Use Tooling (A) in order to plug the plastic tube assemblies. Use Tooling (A) in order to cap the ports in the fuel filter base.
Illustration 2 g03389546
Typical example
Remove secondary filters (6) from canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove bolts (4) from fuel filter base (5). Remove the fuel filter base from the mounting bracket. Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting , "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 3 g03389546
Typical example
Ensure that fuel filter base (5) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Position fuel filter base (5) on the mounting bracket. Install bolts (4). Tighten the bolts to a torque of 44 N m (32 lb ft).
If necessary, install new fuel filters (6) to canisters (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 4 g03389540
Typical example
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies
Cat SIS web machinery list:
Parts bracket Caterpillar catalog:
1P9945
BRACKET AS-FAN
120G, 12G, 130G, 140B, 140G, 14G, 160G, 16G, 3208, 3304, 3306, 3306B, 515, 517, 518C, 525, 527, 528B, 530B, 572G, 621R, 627E, 627F, 627G, 637E, 637G, 814F, 815B, 815F, 816F, 936F, 941, 950, 950B, 951B...
120G, 12G, 130G, 140B, 140G, 14G, 160G, 16G, 3208, 3304, 3306, 3306B, 515, 517, 518C, 525, 527, 528B, 530B, 572G, 621R, 627E, 627F, 627G, 637E, 637G, 814F, 815B, 815F, 816F, 936F, 941, 950, 950B, 951B...
5S5879
BRACKET-SHAFT
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
8S1499
BRACKET AS
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
7S6723
BRACKET-ALTERNATOR
12F, 14E, 215, 235, 330, 330 FM L, 330 L, 330B, 330B L, 350, 515, 518, 518C, 525, 528B, 530B, 561C, 621R, 627, 627B, 627E, 627F, 627G, 637D, 637E, 637G, 639D, 920, 941, 950, 955K, 955L, 966C, 977K, 97...
12F, 14E, 215, 235, 330, 330 FM L, 330 L, 330B, 330B L, 350, 515, 518, 518C, 525, 528B, 530B, 561C, 621R, 627, 627B, 627E, 627F, 627G, 637D, 637E, 637G, 639D, 920, 941, 950, 955K, 955L, 966C, 977K, 97...
8S1498
BRACKET-SHAFT
120G, 130G, 140B, 3304, 3304B, 3306, 3306B, 3306C, 515, 517, 518C, 525, 527, CB-534, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D6D, G3304, G3306, G3306B
120G, 130G, 140B, 3304, 3304B, 3306, 3306B, 3306C, 515, 517, 518C, 525, 527, CB-534, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D6D, G3304, G3306, G3306B
3D5309
BRACKET
120, 120B, 12E, 12F, 140, 140B, 14E
120, 120B, 12E, 12F, 140, 140B, 14E
6F1064
BRACKET
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
5D0395
BRACKET (Right Hand)
12E, 12F, 140, 14E
12E, 12F, 140, 14E
5D0396
BRACKET (Left Hand)
120B, 12E, 12F, 140, 14E
120B, 12E, 12F, 140, 14E
6G5757
BRACKET (L.H.)
120B, 140B
120B, 140B
3D0317
BRACKET
12E
12E
5D0327
BRACKET ASSEM.
120B, 12E, 140, 140B
120B, 12E, 140, 140B
2Y4820
BRACKET
120B, 140B
120B, 140B
2Y2093
BRACKET ASSEM.
120B, 140B
120B, 140B
2D8251
BRACKET ASSEM.
120B, 140B
120B, 140B
7D7675
BRACKET ASSEMBLY
12F, 140, 14E, 16
12F, 140, 14E, 16
3833032
BRACKET AS
Caterpillar
Caterpillar
5D0344
BRACKET
12F, 14E
12F, 14E
6D5721
BRACKET ASSEM.
12F, 14E
12F, 14E
5D5742
BRACKET ASSEM.
12F, 14E
12F, 14E
3D5309
BRACKET
120, 120B, 12E, 12F, 140, 140B, 14E
120, 120B, 12E, 12F, 140, 140B, 14E
6D3259
BRACKET ASSEM.
12F, 14E
12F, 14E
2Y2234
BRACKET
120B, 140B
120B, 140B