AVSPARE.COM
parts catalog

BRACKET 3728025 - Caterpillar



3728025 BRACKET Caterpillar parts 986H BRACKET
Rating:
74
Alternative (cross code) number:
CA3728025
372-8025
3728025
Caterpillar 3728025 BRACKET

Buy BRACKET 3728025 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3728025:

WHEEL LOADER  986H   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

1. Remove nuts (1), cover (2), and the gasket. 2. Put No. 1 piston at the top center compression position (TC) with the following procedure:a. Remove plug (3), two bolts and cover (2) from the flywheel housing. b. Install Tool (B) in the flywheel housing. Use Tool (B) to slowly rotate the engine in the direction of normal rotation, (counterclockwise as seen from the flywheel end of the engine), until timing bolt (4) can be installed in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (5) for the No. 1 cylinder can be moved backward and forward. The No. 1 piston is at the top center compression position (TC) when the timing bolt is installed in the flywheel and both rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position (TC). Remove the timing bolt from the flywheel and rotate the engine in the direction for normal rotation, (counterclockwise as seen from the flywheel end of the engine one full turn 360 degrees, and install the timing bolt again.3. Remove the timing bolt, and use Tool (B) to rotate the engine in the opposite direction of normal rotation (clockwise as seen from the flywheel end of the engine) a minimum of 30 degrees. The timing is correct if Tool (A) and the timing bolt can be installed at the same time. The timing procedure in the Testing & Adjustment Manual must be done again if the timing bolt and Tool (A) can not be installed at the same time.4. Remove the plug from the timing pin hole in the fuel injection pump housing. Install Tool (A) in the timing pin hole. 5. Remove eight bolts (6) and automatic timing advance (7). 6. Remove gear (9) from fuel injection pump camshaft (8).The following steps are for the installation procedure.7. Install gear (9) on fuel injection pump camshaft (8). 8. Install two 3/8 in 16 NC x 6 in (152.4 mm) long guide bolts (10). Space the guide bolts evenly.
There is a light spring located beneath the flyweight cover (12). Hold cover (12) while removing last nut (11). Slowly remove flyweight cover (12) to avoid dropping the spring.
9. Remove four nuts (11) and remove flyweight cover (12). 10. Put automatic timing advance (13) in position on the fuel injection pump camshaft, and install four bolts (14). Tighten bolts (14) just past finger tight. Remove guide bolts (15). 11. Install four nuts (16). Install Tool (C). 12. Tighten four knurled nuts (17) finger tight.
Do not use any tools to tighten the knurled nuts.
13. Install all mounting bolts (14) and tighten to 55 10 N m (41 7 lb ft).14. Loosen knurled nuts (17). Remove four nuts (16) and remove Tool (C).15. Install the spring and flyweight cover

Caterpillar parts catalog:

Caterpillar parts catalog
986H Wheel Loader L8S00001-UP (MACHINE) POWERED BY C15 Engine


Parts bracket Caterpillar catalog:

1647556 BRACKET
1090, 1190, 1190T, 120H, 120K, 120K 2, 120M, 120M 2, 1290T, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 1390, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, ...
3477104 BRACKET AS
374F L, 390F L, 735B, 740B, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 973D, 986H, 988K, C15, C18, CX31-C18I, CX35-C18I, D8T, D9T
1546626 BRACKET AS
1090, 1190, 1190T, 120K, 1290T, 12M, 1390, 140K, 140K 2, 140M, 160K, 2290, 2390, 2391, 2491, 2590, 303.5D, 303E CR, 304D CR, 511, 521, 522, 532, 533, 541, 541 2, 543, 551, 552, 552 2, 621H, 621K, 623K...
1440896 BRACKET AS
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 986H, 988H, IT62G, IT62G II, IT62H
2008895 BRACKET AS
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, 986H, IT62G II, IT62H
2928741 BRACKET AS
12M, 140M, 160M, 16M, 621K, 623K, 623K LRC, 627K, 627K LRC, 834K, 854K, 966H, 972H, 986H, 988K, 992K, 993K, D10T2
1977999 BRACKET AS
980G, 980G II, 980H, 986H
2018357 BRACKET
770G, 770G OEM, 772G, 772G OEM, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797B, 797F, 854K, 966H, 966M, 966M XE, 972H, 972M, 972M XE, 980H, 980M, 982M, 986H, 992K...
3735889 BRACKET
950H, 962H, 966H, 972H, 980H, 986H
3677479 BRACKET AS
950H, 962H, 966H, 972H, 980H, 986H
3677478 BRACKET AS
950H, 962H, 966H, 972H, 980H, 986H
3783708 BRACKET AS
950H, 962H, 966H, 972H, 980H, 986H
4403482 BRACKET-SUPPORT
735B, 740B, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K
3773156 BRACKET AS
834K, 836K, 988K
3735450 BRACKET AS
824K, 825K, 826K, 834K, 836K, 988K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.