AVSPARE.COM
parts catalog

BRACKET AS 3966841 - Caterpillar



3966841 BRACKET AS Caterpillar parts BRACKET
Rating:
71
Alternative (cross code) number:
CA3966841
396-6841
3966841
Caterpillar 3966841 BRACKET AS
Weight: 0.92 pounds 0 kg.

Buy BRACKET AS 3966841 Caterpillar genuine, new aftermarket tractor parts with delivery

You can buy parts: .

$118.00

05 Jul 2021

CN: dodo201354
water pump G5FD156 3800975 3800976 3285324 3925540 3926914 3966841 for 6CT8-3 2300cc engine
HTWCH water pump G5FD156 3800975 3800976 3285324 3925540 3926914 3966841 for 6CT8-3 2300cc engine || water pump || G5FD156 3800975 3800976 || 3926914 3966841 || 6CT8-3 2300cc engine
$63.25

06 Jun 2020

-: -
Water Pump 3966841 FITS Cummins Serie 6CTAA, C8.3L 6C 6CT 6CTA
$87.00

06 Jun 2020
6.0[2.70] Pounds
-: -
3966841 | Cummins Pump- Water
HHP provides parts equal or better in quality compared to the OE at a fraction of the cost. || Products are crafted with hard-wearing materials for long-lasting strength and durability. || Parts meet or exceed OEM specifications to ensure proper fit and function. || Request expert advice from Highway and Heavy Part's ASE Certified Technicians. || Products are only sourced from quality certified manufacturing facilities.
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 1 g02351983
Schematic for the Neutral Flow Bypass solenoid This diagnostic code is for theNeutral Flow Bypass solenoid. An FMI 05 indicates the machine ECM has determined the solenoid circuit current is above normal. The possible causes of this diagnostic code are listed:
The solenoid has failed.
The power wire for the solenoid is shorted to ground.
The machine ECM may have failed, but is unlikely. Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all the machine harnesses and connectors involved in the circuit. Make sure to verify that all of the connections in the circuit are clean, secure, and in good condition. Correct any problems found with any of the connections. Verify the diagnostic code CID 1118 FMI 06 is still active, before continuing with this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the harness connector from the Neutral Flow Bypass solenoid.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the CID 1118 FMI 06 code.Expected Result:The diagnostic code does not change and stays active.Results:
YES - The diagnostic code does not change, and stays active. The circuit is correct. Go to Test Step 2.
NO - The CID 1118 FMI 06 code is no longer active, and has changed to an active CID 1118 FMI 05 code. The solenoid has failed.Repair: Replace the solenoid. Go to test step 3.Test Step 2. CHECK THE SOLENOID POWER WIRE FOR A SHORT.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect both the J1 and J2 harness connectors from the machine ECM.
At the J2 ECM harness connector, measure resistance from contact J2-66 (wire P955-BU) to all contacts that are used in both the J1 and J2 ECM harness connectors. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Go to Test Step 3.
NO - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-66 (wire P955-BU) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. Go to Test Step 3.Test Step 3. CHECK THE DIAGNOSTIC CODE STATUS.
Reconnect all harness connectors. Make sure that the connectors are fully seated. Observe that the clips on each connector are securely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Check the status of the CID 1118 FMI 03 diagnostic code.Expected Result:The CID 1118 FMI 03 diagnostic code is not active.Results:
YES - The CID 1118 FMI 03 diagnostic code is not active and does not exist at this time.

Caterpillar parts catalog:

Caterpillar parts catalog
735C Articulated Truck TFJ00001-UP (MACHINE) POWERED BY C15 Engine
735C Articulated Truck LFJ00001-UP (MACHINE) POWERED BY C15 Engine
745C Articulated Truck TFK00001-UP (MACHINE) POWERED BY C18 Engine
745C Articulated Truck LFK00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck TFN00001-UP (MACHINE) POWERED BY C18 Engine
740C Ejector Articulated Truck LFN00001-UP (MACHINE) POWERED BY C18 Engine


Parts bracket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.