3C8068 BRACKET AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA3C8068
3C-8068
3C8068
CA3C8068
3C-8068
3C8068
Weight: 1 pounds 0 kg.
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M16 - 2 by 8 inch 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01276915
Illustration 2 g01276916
Remove one bolt (2). Insert Tooling (A) in the crankshaft and remove remaining bolts (2) from flex plate (3).
Remove flex plate (3) from the crankshaft. The weight of flex plate (3) is approximately 20 kg (45 lb).
Remove bolts (5) and washers (6). Remove flywheel housing adapter (4) from flywheel housing (1).
Remove bolts (8) and adapter (9) from flex plate (3).
Use a hammer and a punch in order to remove ring gear (7) from flex plate (3). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M16 - 2 by 8 inch 1
B 9S-3263 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01276916
Illustration 4 g01276915Note: Ring gear (7) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when flex plate (3) is installed.
Raise the temperature of ring gear (7). Install ring gear (7) on flex plate (3).
Position adapter (9) and install bolts (8) in flex plate (3).
Install Tooling (A) in the crankshaft.
Position flex plate (3) on the crankshaft. The weight of flex plate (3) is approximately 20 kg (45 lb).
Apply Tooling (B) to the threads of bolts (2).
Install bolts (2). Remove Tooling (A). Install remaining bolt (2).
Tighten bolts (2) to a torque of 300 40 N m (221 30 lb ft).
Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Install flywheel housing adapter (4) on flywheel housing (1).
Install bolts (5) and washers (6). Tighten bolts (5) to a torque of 70 15 N m (52 11 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M16 - 2 by 8 inch 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01276915
Illustration 2 g01276916
Remove one bolt (2). Insert Tooling (A) in the crankshaft and remove remaining bolts (2) from flex plate (3).
Remove flex plate (3) from the crankshaft. The weight of flex plate (3) is approximately 20 kg (45 lb).
Remove bolts (5) and washers (6). Remove flywheel housing adapter (4) from flywheel housing (1).
Remove bolts (8) and adapter (9) from flex plate (3).
Use a hammer and a punch in order to remove ring gear (7) from flex plate (3). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M16 - 2 by 8 inch 1
B 9S-3263 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01276916
Illustration 4 g01276915Note: Ring gear (7) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when flex plate (3) is installed.
Raise the temperature of ring gear (7). Install ring gear (7) on flex plate (3).
Position adapter (9) and install bolts (8) in flex plate (3).
Install Tooling (A) in the crankshaft.
Position flex plate (3) on the crankshaft. The weight of flex plate (3) is approximately 20 kg (45 lb).
Apply Tooling (B) to the threads of bolts (2).
Install bolts (2). Remove Tooling (A). Install remaining bolt (2).
Tighten bolts (2) to a torque of 300 40 N m (221 30 lb ft).
Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Install flywheel housing adapter (4) on flywheel housing (1).
Install bolts (5) and washers (6). Tighten bolts (5) to a torque of 70 15 N m (52 11 lb ft).