3N8841 BRACKET AS Caterpillar parts
3412, 3508, D348, D353C, D379A
Rating:
Alternative (cross code) number:
CA3N8841
3N-8841
3N8841
CA3N8841
3N-8841
3N8841
Weight: 1 pounds 0 kg.
MARINE ENGINE,
Information:
Personal injury or death can result from machine articulation or movement.Machine frames can move and a person can be crushed.Connect the steering frame lock link between the front and rear frames before working on machine.
Personal injury or death can result from escaping fluid under pressure.Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.Always use a board or cardboard when checking for a leak.
The drive shaft rotates between the torque converter and the transmission whenever the engine is running. Contact with the rotating shaft can result in personal injury or death. The rotating shaft is located under the implement and steering pumps.Do not allow personnel into the pump bay area behind the cab when the engine is running.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Test Preparation
Reference: For more information about preparing the machine for troubleshooting, refer to the Service Manual module Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.
Park the machine on a smooth, level surface. Move the machine away from other operating machines and away from personnel.
Permit only one operator on the machine. Keep all other personnel away from the machine or in sight of the operator.
Position the work tool on the ground.
Illustration 1 g03137299
Place the steering frame lock in the LOCKED position.Test Procedure
Check hydraulic oil tank for proper oil level. The proper oil level must be maintained through out the procedure.
Start engine and run engine at low idle. Allow brake accumulators to charge.
Fully apply the service brake.
With service brake applied release the parking brake and reapply the parking brake.
Release the service brake.
Repeat Step 3 through Step 5 three more times.
Turn the engine start switch to the OFF position.
Discharge the brake accumulators by applying and releasing the service brake pedal several times. Continue until the pressure is zero kPa.
Repeat step 1 through step 8 two complete cycles.
Apply and release parking brake switch at one second on and one second off interval fifty times.
Caterpillar parts catalog:
Parts bracket Caterpillar catalog:
8N6142
BRACKET
3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E
3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E
5N5683
BRACKET
3406, 3408, 3412
3406, 3408, 3412
8N0415
BRACKET AS
3408, 3408C, 3412, 3412C, 3412D, 3412E
3408, 3408C, 3412, 3412C, 3412D, 3412E
6N6188
BRACKET AS-MOUNTING
3408, 3412
3408, 3412
8L9725
BRACKET-SWITCH
3408, 3412, 3412C, 3412D, D346, D348, D353C, D379B, D398, D398A, D399, G399
3408, 3412, 3412C, 3412D, D346, D348, D353C, D379B, D398, D398A, D399, G399
4P9200
BRACKET
3406, 3408C, 3412, 3412C, 3412D, 3412E, C27, C32, TH48-E70
3406, 3408C, 3412, 3412C, 3412D, 3412E, C27, C32, TH48-E70
7C6829
BRACKET AS
3412, 3508
3412, 3508
7C6828
BRACKET AS
3412, 3508
3412, 3508
7C6826
BRACKET AS
3408, 3412
3408, 3412
7C6825
BRACKET AS
3406B, 3408, 3412
3406B, 3408, 3412
7C6824
BRACKET AS
3406B, 3408, 3412
3406B, 3408, 3412
3N8818
BRACKET-MOUNTING
3412, 3508, D348, D353C
3412, 3508, D348, D353C