AVSPARE.COM
parts catalog

BRACKET ASSEM. 4D2242 - Caterpillar


4D2242 BRACKET ASSEM. Caterpillar parts 666
Rating:
42
Alternative (cross code) number:
CA4D2242
4D-2242
4D2242
Caterpillar 4D2242 BRACKET ASSEM.
Weight: 2 pounds 1 kg.

Buy BRACKET ASSEM. 4D2242 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL TRACTOR,

Compatible equipment models: 4D2242:

WHEEL TRACTOR  666   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:


Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Escaping fluid under pressure, even a pinhole size leak, can penetrate body tissue, causing serious injury, and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.Always use a board or cardboard when checking for a leak.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines.Dispose of all fluids according to local regulations and mandates.
Torque Converter Operation
Illustration 1 g03416859
(1) Flexplate plate location for engine interface
(2) Inlet
(3) Output Shaft
(4) Outlet
(5) Lockup Clutch The torque converter is mechanically connected to the engine flywheel with a flexplate (1). The torque converter provides a hydraulic connection between the engine and the transmission and is used to increase the torque as the torque load on the machine increases. This is called Torque Converter Drive Mode and is employed when operating in lower gears and when climbing a grade.When torque loads are low, the Transmission/Chassis ECM will engage the Lockup Clutch (5), which then provides a mechanical connection between the engine and transmission. This is Direct Drive Mode and is more fuel efficient and reduces power loss to a minimum, when conditions allow. When ENGAGED, the lockup clutch provides the Direct Drive Mode. The lockup clutch is engaged during transmission shifts to allow a smooth transition between gears. either mode transfers power to the transmission via the torque converter Output Shaft (3)The torque converter inlet relief valve directs oil from the transmission scavenge pump into the torque converter Inlet (2). The torque converter inlet relief valve protects the components of the torque converter by limiting the maximum oil pressure to the torque converter during pressure spikes in the system and when the engine is started and the oil is cold.Oil exiting the torque converter flows through the Outlet (4) to the torque converter outlet relief valve. The torque converter outlet relief valve

Caterpillar parts catalog:

Caterpillar parts catalog
666 TRACTOR 64H00001-UP (MACHINE)


Parts bracket Caterpillar catalog:

3S7189 BRACKET
3304, 3306, 3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 641, 651, 666, 7211, G3516B, HT400, PM-465, PM3412, RM-250C, RM-350B, RR-250, RR-250B, SM-350, SS-250
6D7599 BRACKET ASSEM.
235, 235B, 235C, 235D, 245, 245B, 621, 621B, 623, 627, 627B, 631C, 637, 641B, 650B, 651, 657, 657B, 666, 666B, 814, 815, 816, 824B, 950, 966C, 980B, 988, 992
7D8846 BRACKET ASSEM.
631C, 637, 650B, 657B, 666
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.