AVSPARE.COM
parts catalog

BRACKET 4Z8234 - Caterpillar



4Z8234 BRACKET Caterpillar parts BRACKET
Rating:
51
Alternative (cross code) number:
CA4Z8234
4Z-8234
4Z8234
Caterpillar 4Z8234 BRACKET
Weight: 254 pounds 115 kg.

Buy BRACKET 4Z8234 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01221037
Pump compartment (1) Pressure tap (delivery pressure for drive pump) (2) Pressure tap (delivery pressure for idler pump) (3) Pressure tap (power shift pressure)
Attach a 60000 kPa (8700 psi) pressure gauge to pressure tap (1) .
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Illustration 2 g01267081
Set heavy lift switch (A) to the ON setting. Make sure that the indicator light is on.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Raise the boom until the boom cylinder rods are at full extension.
Check the pressure setting of the heavy lift at pressure tap (1) .
Return the joystick for the boom to the NEUTRAL position.
Illustration 3 g01186845
(4) Main relief valve (5) Locknut for the heavy lift (6) Adjustment screw for the heavy lift (7) Locknut for the main relief valve (8) Adjustment screw for the main relief valveNote: When the main relief setting is adjusted, the heavy lift setting is not affected. When adjustment screw (8) is turned counterclockwise in order to decrease the main relief setting the pressure difference between the main relief setting and heavy lift setting will increase. When adjustment screw (8) is turned clockwise in order to increase the main relief setting the pressure difference between the main relief setting and heavy lift setting will decrease.Note: When the heavy lift setting is increased, the main relief setting is also increased. When the heavy lift setting is decreased, the main relief setting is also decreased.
The relief valve pressure setting for heavy lift should be 38000 500 kPa (5511 73 psi). If the relief valve pressure setting for heavy lift is not within the specification, adjust the relief valve pressure setting for heavy lift.
Loosen locknut (5) in order to adjust the relief valve for the heavy lift. Adjust the pressure by turning adjustment screw for the heavy lift (6) until the pressure gauge reading at pressure tap (1) is 38000 500 kPa (5511 73 psi).Note: Turning adjustment screw (6) clockwise increases the pressure. Turning adjustment screw (6) counterclockwise decreases the pressure.Note: Always make final pressure adjustments on pressure rise.
Tighten locknut (5) to a torque of 70 10 N m (50 7 lb ft).Note: Confirm the heavy lift pressure by raising the boom until the boom cylinder rods are at full extension.
Set heavy lift switch (A) to the OFF setting. The indicator light should not be illuminated.
Raise the boom until the boom cylinders are at full extension.
Check the main relief valve pressure setting at pressure tap (1) .
Return the joystick for the boom to the NEUTRAL position.
The main relief valve pressure setting should be 35000 500 kPa (5075 73 psi). If the main relief valve pressure setting is not within the specification, adjust the main relief valve pressure setting.Note: During adjustment of screw (8), do not allow screw (6) to move.
In order to adjust the


Parts bracket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.