AVSPARE.COM
parts catalog

BRACKET-MOUNTI 5089059 - Caterpillar



5089059 BRACKET-MOUNTI Caterpillar parts BRACKET
Rating:
11
Alternative (cross code) number:
CA5089059
508-9059
5089059
Caterpillar 5089059 BRACKET-MOUNTI
Weight: 0.70 pounds 0 kg.

Buy BRACKET-MOUNTI 5089059 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 8 g00651923
Arc Suppressor with Sure Seal Connectors (1) Pin 1 (2) Pin 2
Illustration 9 g00651621
Arc Suppressor with DT Connectors (1) Pin 1 (2) Pin 2
Place the multimeter in the DIODE test mode.
Place the red probe in the red terminal (positive terminal) of the multimeter.
Place the black probe in the black terminal (negative terminal) of the multimeter.
Place the red probe on Pin 1 of either connector on the arc suppressor. Place the black probe on Pin 2 of either connector.
The multimeter should display a value between 0.5 VDC and 1.0 VDC.
Place the red probe on Pin 2 of either connector of arc suppressor. Place the black probe on Pin 1 of either connector on the arc suppressor.
The multimeter should display OFL or OL.
Place the red probe on pin 1 of the female connector. Place the black probe on pin 1 of the male connector.
The multimeter should have a reading of less than 0.01 VDC.
Place the red probe on Pin 2 of the female connector. Place the black probe on Pin 2 of the male connector.
The multimeter should have a reading of less than 0.01 VDC.
The component is faulty if any of the conditions do not exist.
If the component is faulty, replace the component. 105-8827 Arc Suppressor and 130-0956 Arc Suppressor
Illustration 10 g00651923
Arc Suppressor with Sure Seal Connectors (1) Pin 1 (2) Pin 2
Illustration 11 g00651621
Arc Suppressor with DT Connectors (1) Pin 1 (2) Pin 2
Place the multimeter in the DIODE test mode.
Place the red probe in the red terminal (plus terminal) of the multimeter.
Place the black probe in the black terminal (negative terminal) of the multimeter.
Place the red probe on Pin 1 of either connector on the arc suppressor. Place the black probe on Pin 2 of either connector.
The multimeter should display a value between 0.5 VDC and 1.0 VDC.
Place the red probe on pin 2 of either connector of arc suppressor. Place the black probe on pin 1 of either connector on the arc suppressor.
The multimeter should display OFL or OL.
Place the red probe on pin 1 of the female connector. Place the black probe on pin 1 of the male connector.
The multimeter should have a reading of less than 0.01 VDC.
Place the red probe on pin 2 of the female connector. Place the black probe on pin 2 of the male connector.
The multimeter should have a reading of less than 0.01 VDC.
The component is faulty if any of the conditions do not exist.
If the component is faulty, replace the component. Correct Mounting of Arc Suppressors
Certain arc suppressors may experience failure of the wire leads due to vibration if the arc suppressor is not properly supported.Use a 2U-4497 Strap to tie-wrap the arc suppressor. The arc suppressor should be securely tie-wrapped to a stationary support in order to prevent any motion of the body of the arc suppressor. Additionally, the connectors on both ends of the arc suppressor should be secured.A suitable bracket for supporting an arc suppressor is the 116-6100 Plate . The addition of a 9R-2926 Plate


Parts bracket Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.