AVSPARE.COM
parts catalog

BRACKET 5V3459 - Caterpillar



5V3459 BRACKET Caterpillar parts 920, 930 BRACKET
Rating:
13
Alternative (cross code) number:
CA5V3459
5V-3459
5V3459
Caterpillar 5V3459 BRACKET
Weight: 0.100 pounds 0 kg.

Buy BRACKET 5V3459 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3459:

WHEEL LOADER  920   930   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

1. Remove bolts (1) and the washers that hold rocker shaft assembly (2) in position.2. Remove rocker shaft assembly (2). Remove the O-ring seal from the rear rocker arm support bracket.3. Put identification marks on push rods (3) as to their location in the engine. Remove the push rods.Install Rocker Shaft Assembly & Push Rods
1. Install push rods (1). Make sure they are in their original location in the engine and in position in the valve lifters.
Loosen the adjusting screws on the rocker arms. This will prevent a bent valve or push rod during installation of the rocker shaft assembly.
2. Install a new O-ring seal in the rear rocker arm support bracket. Apply 2P-2506 Thread Lubricant on all of the bolts that hold the rocker shaft assembly in position except for the bolt that goes through the rear rocker arm support bracket.3. Put rocker shaft assembly (2) in position on the engine. Make sure the dowels in the support bracket are in alignment with the dowel holes in the cylinder head. Make sure the rocker arms are engaged with the push rods.4. Install the bolts and washers that hold the rocker shaft assembly in position, and tighten them until they are finger tight.
3304 Engine Sequence
3306 Engine Sequence5. Tighten the bolts that hold the rocker shaft as follows: a. Tighten the bolts in number sequence to a torque of 156 N m (115 lb ft).b. Tighten the bolts in number sequence to a torque of 250 17 N m (185 13 lb ft).c. Tighten the bolts again in number sequence to a torque of 250 17 N m (185 13 lb ft).6. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual. Make an adjustment to the valves so the inlet valves have 0.38 mm (.015 in) clearance and the exhaust valves have 0.64 mm (.025 in) clearance.End By:a. install valve coverDisassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove the plugs from each end of the shaft if necessary.Assemble Rocker Shaft Assembly
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on the rocker shaft. Make sure

Caterpillar parts catalog:

Caterpillar parts catalog
920 WHEEL LOADER 41J04371-UP (MACHINE)
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
966 WHEEL LOADER - 42J06498-UP (MACHINE) POWERED BY 3306 ENGINE
920 WHEEL LOADER 41J04371-UP (MACHINE)
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
966 WHEEL LOADER - 42J06498-UP (MACHINE) POWERED BY 3306 ENGINE
920 WHEEL LOADER 41J04371-UP (MACHINE)
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE


Parts bracket Caterpillar catalog:

5S5879 BRACKET-SHAFT
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
8S1499 BRACKET AS
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, ...
7N8015 BRACKET
120G, 12G, 130G, 140G, 14G, 160G, 1673C, 225, 235, 330 L, 3304, 3304B, 3306, 3306B, 330B, 515, 517, 518C, 525, 527, 572G, 615C, 627E, 637D, 637E, 815B, 920, 936F, 951B, 966C, CB-534, D250B, D25C, D300...
7K1402 BRACKET
153, 235, 235B, 235C, 235D, 245, 245B, 245D, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 3618, 572G, 578, 627B, 65, 65C, 65E, 75C, 75D, 75E, 776D, 777D, 797, 797B, 797...
7S6723 BRACKET-ALTERNATOR
12F, 14E, 215, 235, 330, 330 FM L, 330 L, 330B, 330B L, 350, 515, 518, 518C, 525, 528B, 530B, 561C, 621R, 627, 627B, 627E, 627F, 627G, 637D, 637E, 637G, 639D, 920, 941, 950, 955K, 955L, 966C, 977K, 97...
3N4082 BRACKET
215, 229, 245, 3208, 3304, 3406, 3412, 815B, 920, 941, 943, 955L, 963, 980F, D4H, D5H, D7G, G936
5D2845 BRACKET
16, 225, 245, 623, 631C, 641B, 814, 826B, 910, 920, 950, 966C, 980B, 992, D5, D6C, D7F, D8H, D9G
2P7848 BRACKET
120G, 528, 920, 930, 950, 950B, D6C, G936
8S0863 BRACKET ASSEM.
12F, 14E, 561C, 920, 966C, 977K, D5, D6C
1V0593 BRACKET ASSEM.
528, 528B, 530B, 613B, 920, 930
4V8141 BRACKET
920, 950, 966C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.