1764172 BRIDGE AS-VALVE Caterpillar parts
3176, 3176B, 3176C, 3196, C-10, C-12
Rating:
Alternative (cross code) number:
CA1764172
176-4172
1764172
CA1764172
176-4172
1764172
Weight: 0.30 pounds 0 kg.
INDUSTRIAL ENGINE, TRUCK ENGINE,
Related part:
1764172
BRIDGE AS-YM
4574600
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$49.85
24 Mar 2019
Unknown: Unknown
Caterpillar 1764172 Bridge AS- New
$34.15
27 Jul 2018
40 Hundredths Pounds
CTP: CTP
Caterpillar 176-4172 Rocker Arms (1764172)
1764172 Caterpillar, Engine Parts Weight(lbs): 0.40 Length(cm): 5.8000 Width(cm): 4.9000 Depth(cm): 6.1000
1764172 Caterpillar, Engine Parts Weight(lbs): 0.40 Length(cm): 5.8000 Width(cm): 4.9000 Depth(cm): 6.1000
This part in 4 request:
Show.
This information for suppliers only!
2025-09-04
2022-08-03
2022-08-03
2022-08-03
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 1764172:
Information:
Remove And Install Connecting Rod Bearings
start by:a) remove oil pan 1. Turn the crankshaft until two pistons are at bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the bearings from the caps.2. Push the connecting rods away from the crankshaft and remove the upper half of the bearings.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.3. Clean the surfaces where the bearings fit. Install the upper half of the bearing in the connecting rod. Pull the connecting rod slowly on to the crankshaft.4. Install lower half of the bearing in the cap.
When the connecting rod caps are installed, make sure that the numbers on the side of the caps are next to and respective with the number on the side of the connecting rods.
5. Check the bearing clearance with Plastigage (A). Put Plastigage (A) on the bearing.6. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.
Do not use an impact wrench to tighten the nuts the additional 60 5°.
Do not turn the crankshaft when Plastigage (A) is in position. 7. Put caps (1) in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60° 5° more.8. Remove the caps. Measure the thickness of Plastigage (A). The rod bearing clearance must be .0021 to .0055 in. (0.053 to 0.140 mm). The maximum permissible clearance is .006 in. (0.15 mm).9. Put the caps in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60° 5° more.10. Do Steps 1 through 7 again for other bearings.end by:a) install oil pan
start by:a) remove oil pan 1. Turn the crankshaft until two pistons are at bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the bearings from the caps.2. Push the connecting rods away from the crankshaft and remove the upper half of the bearings.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.3. Clean the surfaces where the bearings fit. Install the upper half of the bearing in the connecting rod. Pull the connecting rod slowly on to the crankshaft.4. Install lower half of the bearing in the cap.
When the connecting rod caps are installed, make sure that the numbers on the side of the caps are next to and respective with the number on the side of the connecting rods.
5. Check the bearing clearance with Plastigage (A). Put Plastigage (A) on the bearing.6. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.
Do not use an impact wrench to tighten the nuts the additional 60 5°.
Do not turn the crankshaft when Plastigage (A) is in position. 7. Put caps (1) in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60° 5° more.8. Remove the caps. Measure the thickness of Plastigage (A). The rod bearing clearance must be .0021 to .0055 in. (0.053 to 0.140 mm). The maximum permissible clearance is .006 in. (0.15 mm).9. Put the caps in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60° 5° more.10. Do Steps 1 through 7 again for other bearings.end by:a) install oil pan
Cat SIS web machinery list:
Parts bridge Caterpillar catalog:
140H, 143H, 14H, 160H, 163H, 16H, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 572R II, 65E, 725, 730, 75C, 75D, 75E, 814F, 815F, 816F, 85C, 85D, 85E, 95E, 966G I...
7E6887
BRIDGE AS
3176, 75
3176, 75
7E8857
BRIDGE AS-VALVE
3176, 75
3176, 75
1382554
BRIDGE AS-VALVE
3176B
3176B
6I1659
BRIDGE AS-VALVE
3176B, R1700 II
3176B, R1700 II
6I4584
BRIDGE AS-EXHAUST
3176B
3176B
6I1683
BRIDGE AS-EXHAUST
3406B, 3406C
3406B, 3406C
7C0049
BRIDGE AS-EXHAUST
3406B, 3406C, D350E, D400E
3406B, 3406C, D350E, D400E
3406B, 3406C, D350E, D400E
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...
6I2490
BRIDGE-VALVE
3608, 3612, 3616
3608, 3612, 3616
1457384
BRIDGE-VALVE
3126B, 325C
3126B, 325C
6I4584
BRIDGE AS-EXHAUST
3176B
3176B
6I1659
BRIDGE AS-VALVE
3176B, R1700 II
3176B, R1700 II
1382554
BRIDGE AS-VALVE
3176B
3176B