BUCKET AS-HEAVY DUTY 2980179 - Caterpillar

2980179 BUCKET AS-HEAVY DUTY Caterpillar parts 324D L, 325D L, 329D L, 330D L, 336D L

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2980179
298-0179
2980179

Caterpillar 2980179 BUCKET AS-HEAVY DUTY

Buy BUCKET AS-HEAVY DUTY 2980179 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2980179:

EXCAVATOR 324D L 325D L 329D L 330D L 336D L Caterpillar

Number on catalog scheme:

Caterpillar 2980179 Parts scheme BUCKET AS-HEAVY DUTY

For full view, you need register

Information:

Illustration 1 g01045652
Schematic diagram of the output for the warning lampThe engine is equipped with a remote control panel that includes a status control module.
Illustration 2 g01045653
Schematic diagram of the output for the warning lampThe engine is configured for Canadian Standards Association (CSA).Test Step 1. Inspect the Electrical Connectors and the Wiring
Set the engine control to the OFF/RESET mode. Remove the electrical power from the engine.Note: For the following steps, refer to Troubleshooting, "Inspecting Electrical Connectors".
Thoroughly inspect each of the following connectors:
EIS connectors on the control module
Connections for the equipment that is connected to the output for the warning lamp
Illustration 3 g01047061
Harness side of the EIS connector (EISC-C) Output for the warning lamp
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the output for the warning lamp.
Check the terminal strips for corrosion and for mechanical failure.
If the engine is equipped for CSA, check the harnesses and the wiring for abrasion and for pinch points between the device that is connected to the output and the control module.Expected Result:The connectors, pins, and sockets are connected properly. The terminal strips do not have corrosion or mechanical failure. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - The components are in good condition with proper connections.
Not OK - The components are not in good condition and/or at least one connection is improper.Repair: Perform the necessary repairs and/or replace parts, if necessary.STOPTest Step 2. Check for an Open Circuit
Disconnect the EIS connector.
At the output device, identify the wire that runs to the EIS control module. Disconnect the end of the wire from the device. This will isolate the wire.
Check the continuity of the wiring between terminal EISC-C and the end of the wire that was removed from the output device.Expected Result:The wiring has continuity.Results:
OK - The wiring has continuity.Repair: Perform the following procedure:
Check the continuity of the output device. If the output device does not have continuity, replace the output device. STOP.
Check the continuity of the wiring between the output device and +Battery. If the wiring does not have continuity, repair the wiring or replace the wiring. STOP.
Reconnect the end of the wire to the output device. Restore electrical power to the engine and check the operation of the output for the warning lamp. If the output operates correctly, the problem is resolved. STOP. If the output does not operate correctly, proceed to Test Step 3.
Not OK - The wiring does not have continuity.Repair: Repair the connection and/or the wire, when possible. Replace parts, if necessary. Verify that the problem is resolved.STOPTest Step 3. Check for a Short Circuit
Verify that electrical power is removed from the engine.
Verify that the EIS connector is disconnected.
At the output device, identify the wire that runs to the EIS control module. Disconnect the end of the wire from the device. This will isolate the wire.
Measure the resistance between terminal EISC-C and all of the other terminals on the EIS connector.Expected Result:All of the measurements indicate an open