3686460 BUCKET AS-GENERAL PURPOSE Caterpillar parts
966H, 966K, 966M, 966M XE, 972K
Rating:
Alternative (cross code) number:
CA3686460
368-6460
3686460
CA3686460
368-6460
3686460
WHEEL LOADER,
Information:
Removal Procedure
Start By:
Install the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01313860Note: Mark the positions of the engine supports and the shims for proper installation. The right side engine supports are connected to the plates on the generator base by dowels. The dowels must be removed before the mounting supports can be removed.
Remove the plastic caps from the engine supports to the access hole for the dowels. Use a 1/2 inch bolt with a washer in order to remove the dowels, if necessary.
Attach a suitable lifting device to the engine lifting brackets. The weight of the C280-06 Engine is approximately 15700 kg (34600 lb). The weight of the C280-08 Engine is approximately 19000 kg (41900 lb).
Remove bolts (1) that hold engine supports (2) to the generator base. Check the O-ring seals on the bolts for damage. If necessary, replace the O-ring seals. The O-ring seals should be installed on clean bolts.
Lift the engine enough in order to place a suitable lifting device around engine support (2). Use the forcing bolt in order to help lift the engine. The weight of each engine support (2) is approximately 60 kg (130 lb).
Remove the shims, if necessary.
Remove bolts (3) that hold engine support (2) to the cylinder block.
Tap engine support (2) with a rubber mallet in order to loosen dowels (4) from the cylinder block.
Remove engine support (2) from the side of the cylinder block.
If necessary, remove dowels (4) from engine support (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01313860
If dowels (4) were removed from engine support (2), install the dowels. The dowels must extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of engine support (2). Check the O-ring seals for damage. If necessary, replace the O-ring seals.
Use a suitable lifting device to place engine support (2) in position on the side of the cylinder block. The weight of each engine support (2) is approximately 60 kg (130 lb). Install bolts (3). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Install the shims in the original location, if necessary.
Install the dowels through engine support (2) and into the base on the right side of the engine, if necessary.
Lower the engine onto the base assembly. The weight of the C280-06 Engine is approximately 15700 kg (34600 lb). The weight of the C280-08 Engine is approximately 19000 kg (41900 lb). Remove the forcing bolt when you lower the engine. Install bolts (1).
Check the alignment between the engine and the driven equipment.
Perform the following check for soft foot:
Soft foot is measured with a dial indicator. Mount a dial indicator from the base assembly to the top of the foot next to the engine block. Be sure that all the jacking screws are loose. While one foot at a time is loosened, the
Start By:
Install the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01313860Note: Mark the positions of the engine supports and the shims for proper installation. The right side engine supports are connected to the plates on the generator base by dowels. The dowels must be removed before the mounting supports can be removed.
Remove the plastic caps from the engine supports to the access hole for the dowels. Use a 1/2 inch bolt with a washer in order to remove the dowels, if necessary.
Attach a suitable lifting device to the engine lifting brackets. The weight of the C280-06 Engine is approximately 15700 kg (34600 lb). The weight of the C280-08 Engine is approximately 19000 kg (41900 lb).
Remove bolts (1) that hold engine supports (2) to the generator base. Check the O-ring seals on the bolts for damage. If necessary, replace the O-ring seals. The O-ring seals should be installed on clean bolts.
Lift the engine enough in order to place a suitable lifting device around engine support (2). Use the forcing bolt in order to help lift the engine. The weight of each engine support (2) is approximately 60 kg (130 lb).
Remove the shims, if necessary.
Remove bolts (3) that hold engine support (2) to the cylinder block.
Tap engine support (2) with a rubber mallet in order to loosen dowels (4) from the cylinder block.
Remove engine support (2) from the side of the cylinder block.
If necessary, remove dowels (4) from engine support (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01313860
If dowels (4) were removed from engine support (2), install the dowels. The dowels must extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of engine support (2). Check the O-ring seals for damage. If necessary, replace the O-ring seals.
Use a suitable lifting device to place engine support (2) in position on the side of the cylinder block. The weight of each engine support (2) is approximately 60 kg (130 lb). Install bolts (3). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Install the shims in the original location, if necessary.
Install the dowels through engine support (2) and into the base on the right side of the engine, if necessary.
Lower the engine onto the base assembly. The weight of the C280-06 Engine is approximately 15700 kg (34600 lb). The weight of the C280-08 Engine is approximately 19000 kg (41900 lb). Remove the forcing bolt when you lower the engine. Install bolts (1).
Check the alignment between the engine and the driven equipment.
Perform the following check for soft foot:
Soft foot is measured with a dial indicator. Mount a dial indicator from the base assembly to the top of the foot next to the engine block. Be sure that all the jacking screws are loose. While one foot at a time is loosened, the
Caterpillar SIS machinery equipment:
Caterpillar SIS
950L Wheel Loader LXX00001-UP (MACHINE) POWERED BY C7.1 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M XE Wheel Loader B8P00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M Wheel Loader LMM00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M Wheel Loader L8R00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966L Wheel Loader FSL00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M Wheel Loader GMS00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M XE Wheel Loader XCR00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
Loader Buckets (without Hydraulics) 7NW00001-UP (MACHINE) »
368-6460
BUCKET AS-GENERAL PURPOSE
966H Wheel Loader TAL00001-UP (MACHINE) POWERED BY C11 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966K Wheel Loader TFS00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966K Wheel Loader PBG00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
972K Wheel Loader PEM00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966K Series XE Wheel Loader NGX00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M Wheel Loader KJP00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M Wheel Loader DYC00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966H Wheel Loader BJ600001-UP (MACHINE) POWERED BY C11 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
966M XE Wheel Loader P6C00001-UP (MACHINE) POWERED BY C9.3 Engine »
368-6460
BUCKET AS-GENERAL PURPOSE
Caterpillar parts catalog:
Parts bucket Caterpillar catalog:
3854338
BUCKET GP-MATERIAL HANDLING
966K, 966M XE
966K, 966M XE
3899206
BUCKET GP-MATERIAL HANDLING
966K, 966M XE
966K, 966M XE
3915545
BUCKET GP-MATERIAL HANDLING
966K, 966M XE
966K, 966M XE
3924138
BUCKET GP-MATERIAL HANDLING
966K, 966M XE
966K, 966M XE
3928759
BUCKET GP-MATERIAL HANDLING
966K, 966M XE
966K, 966M XE
3944384
BUCKET GP-ROCK
966K, 966M XE
966K, 966M XE
4378265
BUCKET AS-MATERIAL HANDLING
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3972527
BUCKET AS-MATERIAL HANDLING
966H, 966K
966H, 966K
3988120
BUCKET AS-MATERIAL HANDLING
972H, 972K
972H, 972K
3143185
BUCKET AS-MATERIAL HANDLING
966H, 966M, 972H, 972M
966H, 966M, 972H, 972M
3752975
BUCKET AS-GENERAL PURPOSE
Caterpillar
Caterpillar
1741984
BUCKET GP-GENERAL PURPOSE
Caterpillar
Caterpillar
3635197
BUCKET GP-GENERAL PURPOSE
966H, 966K, 966M, 966M XE, 972K
966H, 966K, 966M, 966M XE, 972K
3143235
BUCKET AS-ROCK
966M, 972H, 972M
966M, 972H, 972M
3143236
BUCKET AS-ROCK
966H, 966M, 972M
966H, 966M, 972M
2397647
BUCKET & ADJUSTER GP
320C, 322B L, 322C, 324D L
320C, 322B L, 322C, 324D L