AVSPARE.COM
parts catalog

BUMPER 2H9447 - Caterpillar



2H9447 BUMPER Caterpillar parts BUMPER
Rating:
21
Alternative (cross code) number:
CA2H9447
2H-9447
2H9447
Caterpillar 2H9447 BUMPER
Weight: 0.35 pounds 0 kg.

Buy BUMPER 2H9447 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01269165
Schematic for theImplement Shutoff Solenoid ValveThis diagnostic code is associated with theImplement Shutoff Solenoid Valve. The FMI 03 means that the ECM has detected that the voltage of the solenoid circuit is above normal or that the ECM has detected voltage in the circuit when no voltage should be present.Conditions that could cause this diagnostic code to be activated are:
The energize circuit of the solenoid is shorted to another voltage source.
The ECM has failed. This situation is unlikely.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Note: The resistance of the solenoid coil should be 7.5 0.4 ohms at 20 °C (68.0 °F).Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect the machine harness connector from the solenoid. Disconnect the machine harness connectors J1 and J2 from the ECM.
At the machine harness ECM connectors, measure the resistance from contact J2-6 (wire M927-GN) to all of the other contacts that are used in the J1 and J2 connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
YES - Each resistance measurement is greater than 5000 ohms. The resistance measurement does not indicate a short in the machine harness. Proceed to Test Step 2.
NO - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. Repair: The short is between wire G953-BU and the circuit that has a low resistance measurement.For information on testing for short circuits and finding short circuits, refer to Testing and Adjusting, "Wiring Harness (Short Circuit) - Test". Repair the machine harness or replace machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECMThe key start switch remains in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the machine harness connector J2 for the ECM, use a 151-6320 Removal Tool to remove the solenoid energize wire G953-BU and socket at contact J2-7 from the harness connector.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Reconnect the negative battery cable and Turn the key start switch to the ON position.
Observe the status of the active CID 0358 FMI 03 diagnostic code.Expected Result:The CID 0358 FMI 03 diagnostic code is no longer active. A CID 0358 FMI 05 diagnostic code is now active.Results:
YES - The CID 0358 FMI 03 diagnostic code is no longer active. A CID 0358 FMI 05 diagnostic code has been activated


Parts bumper Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.