BUMPER 2V3726 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components. Use fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Bearing (Ball) - Lubricate
Engine Air Cleaner Element - Replace
Engine Oil Filter - Change
Fumes Disposal Filter Differential Pressure - Check
Fumes Disposal Filter - Drain
Fumes Disposal Filter Element - Replace
Generator - Dry
Generator Set - Test
Insulation - Test
Overhaul Considerations
Rotating Rectifier - Test
Space Heater - Check
Varistor - Test
Winding - Test
Daily
Air Inlet Filter - Check
Air Tank Moisture and Sediment - Drain
Bearing Temperature - Measure/Record
Cooling System Coolant Level - Check
Electrical Connections - Check
Electrohydraulic System - Inspect
Engine Air Cleaner Service Indicator - Inspect
Engine Air Precleaner - Clean
Engine Oil Level - Check
Fuel System Fuel Filter Differential Pressure - Check
Fumes Disposal Filter Differential Pressure - Check
Generator - Inspect
Generator Load - Check
Power Factor - Check
Stator Winding Temperature - Measure/Record
Voltage and Frequency - Check
Walk-Around Inspection
Every Week
Automatic Start/Stop - Inspect
Initial 250 Service Hours
Crankcase Blowby - Measure/Record
Cylinder Pressure - Measure/Record
Engine Oil Sample - Obtain
Engine Valve Lash and Bridge - Adjust
Valve Stem Projection - Measure/Record
Every 250 Service Hours
Battery Electrolyte Level - Check
Every 500 Service Hours
Cooling System Coolant Sample (Level 1) - Obtain
Fumes Disposal Filter - Drain
Initial 1000 Service Hours
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Speed/Timing Sensor - Clean/Inspect
Every 1000 Service Hours
Aftercooler Condensation - Drain
Alternator - Inspect
Belts - Inspect/Adjust/Replace
Cooling System Coolant Sample (Level 2) - Obtain
Crankcase Pressure - Measure
Crankshaft Vibration Damper - Inspect
Engine Crankcase Breather - Clean
Engine Oil - Change
Engine Oil Filter (Auxiliary) - Change
Engine Oil Filter - Change
Engine Oil Sample - Obtain
Engine Valve Lash and Bridge - Adjust
Exhaust Piping - Inspect
Gas Pressure Regulator Condensation - Drain
Hoses and Clamps - Inspect/Replace
Ignition System Spark Plugs - Inspect/Adjust/Replace
Ignition System Timing - Check/Adjust
Inlet Air System - Inspect
Oxygen Sensor - Calibrate
Radiator - Clean
Valve Stem Projection - Measure/Record
Every 2000 Service Hours
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Speed/Timing Sensor - Clean/Inspect
Stator Lead - Check
Every 4000 Service Hours
Crankcase Blowby - Measure/Record
Cylinder Pressure - Measure/Record
Electrohydraulic System Oil - Change
Electrohydraulic System Oil Filter - Change
Engine Mounts - Check
Engine Protective Devices - Check
Exhaust Bypass - Inspect
Fuel Metering Valve Screen - Check
Starting Motor - Inspect
Water Pump - Inspect
Every 5000 Service Hours
Fumes Disposal Filter - Drain
Every 8000 Service Hours
Fumes Disposal Filter Element - Replace
Rotating Rectifier - Check
Turbocharger - Inspect
Water Temperature Regulator - Replace
Between 10 000 and 20 000 Service Hours
Generator Bearing - Inspect
Overhaul (Top End)
Every 24 000 Service Hours or 3 Years
Cooling System Coolant (NGEC) - Change
Between 30 000 and 60 000 Service Hours
Generator Bearing - Inspect
Overhaul (In-Frame)
Between