1053015 BUSHING Caterpillar parts
527, D5H, D5H XL, D5HTSK II
Rating:
Alternative (cross code) number:
CA1053015
105-3015
1053015
CA1053015
105-3015
1053015
Weight: 3 pounds 1 kg.
Information:
ID
88.92
mm
OD
114.32
mm
WIDTH
63
mm
TRACK SKIDDER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1053015 - Synder General OEM Replacement Heat Pump Defrost Sensor
OEM Replm for Synder General This is a Brand New OEM Replacement Heat Pump Defrost Sensor || Top Qualty OEM Replacement Part!
OEM Replm for Synder General This is a Brand New OEM Replacement Heat Pump Defrost Sensor || Top Qualty OEM Replacement Part!
1053015 - Comfort Maker OEM Replacement Heat Pump Defrost Sensor
OEM Replm for Comfort Maker This is a Brand New OEM Replacement Heat Pump Defrost Sensor || Top Qualty OEM Replacement Part!
OEM Replm for Comfort Maker This is a Brand New OEM Replacement Heat Pump Defrost Sensor || Top Qualty OEM Replacement Part!
Compatible equipment models: 1053015:
Information:
Note: Use this procedure only if the engine does not shut down completely.Probable Causes
Check for active event codes that may derate engine power
Electrical connections not properly connected.
Check for intermittent diagnostic codes
Intermittent throttle signal
Fuel system components
Fuel supply pressure
Restriction in the air inlet and exhaust system
Excessive temperature of the turbocharger that causes the engine derate Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Event Codes
A. Certain event codes may derate engine power. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes.
   
Event codes    
Result: An event code is active or logged.
Troubleshoot any codes that are present before continuing with this procedure.
Result: An event code is not active or logged.
Proceed to Test Step 2.
   
2. Electrical Connections
A. Verify that the following connectors are installed correctly:
1. Electrical connectors for the ECM
2. Connectors for the wiring harness under the valve cover
3. Connectors for the engine speed/timing sensors
   
Electrical connectors    
Result: The connectors are installed correctly.
Proceed to Test Step 3.
Result: The connectors are not installed correctly.
Install the connectors correctly. Refer toTroubleshooting, "Electrical Connectors - Inspect" for the proper troubleshooting procedure.
   
3. Check for Intermittent Diagnostic Codes
A. Certain diagnostic codes may cause poor performance. Connect Cat ET and check for active codes and/or for logged codes.
   
Intermittent codes    
Result: Intermittent codes are present.
Troubleshoot any codes that are present before continuing with this procedure.
Result: Intermittent codes are not present.
Proceed to Test Step 4.
   
4. Intermittent Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET.
B. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Refer to Troubleshooting, "Speed Control - Test".
   
Throttle signal    
Result: The status for "Throttle Position" is stable.
Proceed to Test Step 5.
Result: The status for "Throttle Position" is not stable.
Make the necessary repairs. Refer to Troubleshooting, "Speed Control - Test".
   
5. Fuel System
A. Ensure that the fuel system is operating properly.
B. Start the engine.
C. Access the Cylinder Cutout Test in the Diagnostic Tests under the "Diagnostics" menu.
D. Select the "Automatic Cylinder Cutout Test" on Cat ET.
E. Start the test.
   
Cylinder cutout test    
Result: The "Cylinder Cutout Test" was successful.
Proceed to Test Step 6.
Result: The "Cylinder Cutout Test" was not successful.
Repair the cylinders that failed the "Cylinder Cutout Test". Reset all active codes and clear all logged codes. Verify that the repair has eliminated the problem in the cylinder.
   
6. Fuel Supply Pressure
A. Check the fuel pressure. Ensure that the fuel is stable. Refer to Systems Operation/Testing and Adjusting for the procedure to check the fuel pressure manually.
B. Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, purge the air from the fuel system.
C. Ens
Check for active event codes that may derate engine power
Electrical connections not properly connected.
Check for intermittent diagnostic codes
Intermittent throttle signal
Fuel system components
Fuel supply pressure
Restriction in the air inlet and exhaust system
Excessive temperature of the turbocharger that causes the engine derate Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Event Codes
A. Certain event codes may derate engine power. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes.
   
Event codes    
Result: An event code is active or logged.
Troubleshoot any codes that are present before continuing with this procedure.
Result: An event code is not active or logged.
Proceed to Test Step 2.
   
2. Electrical Connections
A. Verify that the following connectors are installed correctly:
1. Electrical connectors for the ECM
2. Connectors for the wiring harness under the valve cover
3. Connectors for the engine speed/timing sensors
   
Electrical connectors    
Result: The connectors are installed correctly.
Proceed to Test Step 3.
Result: The connectors are not installed correctly.
Install the connectors correctly. Refer toTroubleshooting, "Electrical Connectors - Inspect" for the proper troubleshooting procedure.
   
3. Check for Intermittent Diagnostic Codes
A. Certain diagnostic codes may cause poor performance. Connect Cat ET and check for active codes and/or for logged codes.
   
Intermittent codes    
Result: Intermittent codes are present.
Troubleshoot any codes that are present before continuing with this procedure.
Result: Intermittent codes are not present.
Proceed to Test Step 4.
   
4. Intermittent Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET.
B. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Refer to Troubleshooting, "Speed Control - Test".
   
Throttle signal    
Result: The status for "Throttle Position" is stable.
Proceed to Test Step 5.
Result: The status for "Throttle Position" is not stable.
Make the necessary repairs. Refer to Troubleshooting, "Speed Control - Test".
   
5. Fuel System
A. Ensure that the fuel system is operating properly.
B. Start the engine.
C. Access the Cylinder Cutout Test in the Diagnostic Tests under the "Diagnostics" menu.
D. Select the "Automatic Cylinder Cutout Test" on Cat ET.
E. Start the test.
   
Cylinder cutout test    
Result: The "Cylinder Cutout Test" was successful.
Proceed to Test Step 6.
Result: The "Cylinder Cutout Test" was not successful.
Repair the cylinders that failed the "Cylinder Cutout Test". Reset all active codes and clear all logged codes. Verify that the repair has eliminated the problem in the cylinder.
   
6. Fuel Supply Pressure
A. Check the fuel pressure. Ensure that the fuel is stable. Refer to Systems Operation/Testing and Adjusting for the procedure to check the fuel pressure manually.
B. Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, purge the air from the fuel system.
C. Ens
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
2213197
BUSHING
D5H, D5R LGP, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
D5H, D5R LGP, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
7P6596
BUSHING
527, 943, 953, 953C, 953D, 963, D5H, D5H XL, D5HTSK II, D5R LGP, D6H, D6H II, D6M, D6N, D6N LGP, D6N OEM
527, 943, 953, 953C, 953D, 963, D5H, D5H XL, D5HTSK II, D5R LGP, D6H, D6H II, D6M, D6N, D6N LGP, D6N OEM
3T8336
BUSHING
D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D6M
D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D6M
6Y0306
BUSHING
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 517, 527, 561M, 561N, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 517, 527, 561M, 561N, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
8G3202
BUSHING
D4HTSK III, D5H, D5H XL, D5HTSK II, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
D4HTSK III, D5H, D5H XL, D5HTSK II, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
9J5284
BUSHING
24H, 24M, 527, 621K, 627K, 627K LRC, 824C, 824G, 824G II, 824H, 824K, 825K, 826C, 826G, 826G II, 826H, 826K, 844, 844K, 8A, 8S, D5H, D5H XL, D5HTSK II, D6M, D6N, D7E, D7E LGP, D8K, D8L, D9R, D9T, OEMS
24H, 24M, 527, 621K, 627K, 627K LRC, 824C, 824G, 824G II, 824H, 824K, 825K, 826C, 826G, 826G II, 826H, 826K, 844, 844K, 8A, 8S, D5H, D5H XL, D5HTSK II, D6M, D6N, D7E, D7E LGP, D8K, D8L, D9R, D9T, OEMS
2213202
BUSHING
D5H, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
D5H, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
6Y6236
BUSHING
527, D5H, D5H XL, D5HTSK II
527, D5H, D5H XL, D5HTSK II
6D0217
BUSHING
517, 527, 769, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
517, 527, 769, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
7J9682
BUSHING
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 920, 930, 930R, 941, 951B, 955C, 966D, 966F, 966F II, 970F, AD30, D5H, D5H XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP...
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 920, 930, 930R, 941, 951B, 955C, 966D, 966F, 966F II, 970F, AD30, D5H, D5H XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP...
2K0227
BUSHING
515, 517, 525, 525B, 527, 528, 528B, 530B, 615, 615C, 623B, 623E, 633D, 931B, 931C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
515, 517, 525, 525B, 527, 528, 528B, 530B, 615, 615C, 623B, 623E, 633D, 931B, 931C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
2582305
BUSHING
517, 527, 583R, 587R, 587T, D6R, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR, D8R, D8R II, D8T, PL87
517, 527, 583R, 587R, 587T, D6R, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR, D8R, D8R II, D8T, PL87
6D0217
BUSHING
517, 527, 769, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
517, 527, 769, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
6Y6236
BUSHING
527, D5H, D5H XL, D5HTSK II
527, D5H, D5H XL, D5HTSK II
8E6526
BUSHING-TERMINAL
527, D5H, D5H XL, D6M
527, D5H, D5H XL, D6M
2296915
BUSHING-TRACK
953C, 953D, D5H
953C, 953D, D5H
1090481
BUSHING-TRACK
D5H, D6M
D5H, D6M
4T0987
BUSHING
320C, 320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 32...
320C, 320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 32...
9T8115
BUSHING-TERMINAL
D6H, D6H XL, D6H XR, D6R
D6H, D6H XL, D6H XR, D6R
2304512
BUSHING-TRACK
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II, D6R III
527, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II, D6R III
6Y2130
BUSHING AS
572R, 572R II, 583R, 583T, 587R, 587T, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T LGP, D6T LGPPAT, D7H, D7R, D7R II, D7R XR, D8T, D9R, D9T, PL83
572R, 572R II, 583R, 583T, 587R, 587T, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T LGP, D6T LGPPAT, D7H, D7R, D7R II, D7R XR, D8T, D9R, D9T, PL83
3E4876
BUSHING AS
572R, 572R II, 583R, 587R, 587T, D10N, D10R, D11N, D11R, D11T, D6H, D6H XL, D6H XR, D6R, D6R II, D7H, D7R, D7R II, D9R
572R, 572R II, 583R, 587R, 587T, D10N, D10R, D11N, D11R, D11T, D6H, D6H XL, D6H XR, D6R, D6R II, D7H, D7R, D7R II, D9R
7J9682
BUSHING
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 920, 930, 930R, 941, 951B, 955C, 966D, 966F, 966F II, 970F, AD30, D5H, D5H XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP...
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 920, 930, 930R, 941, 951B, 955C, 966D, 966F, 966F II, 970F, AD30, D5H, D5H XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP...