1195200 BUSHING Caterpillar parts
318B, 320B
Rating:
Alternative (cross code) number:
CA1195200
119-5200
1195200
CA1195200
119-5200
1195200
Weight: 1 pounds 0 kg.
Information:
ID
80
mm
OD
90
mm
WIDTH
90
mm
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1195200 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 1195200 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
11A
For full view, you need register
Information:
System Operation Description:Use this procedure in order to determine if the "Wait to Start Lamp" is operating correctly.The "Wait To Start Lamp" parameter can be programmed to "J1/P1:31", to "J1939", or to "None". When the parameter is programmed to "J1/P1:31" a lamp circuit can be connected to terminal 31 in order to indicate that the air inlet heater is on and the engine is not running. "Fast Idle Enabled Lamp" must be programmed to "J1/P1:21" for this feature to be used.Note: This feature is only available when "Truck Manufacturer" is programmed to "Other".Electrical Connection of LampsOne terminal of the lamp must be connected to battery voltage through the vehicle wiring. The other terminal is connected to the Engine Control Module (ECM) at the vehicle harness connector J1/P1 at terminal 31.The ECM provides a path to ground in order to turn on the lamp.
Illustration 1 g00770585
Circuit schematic for the wait to start lamp
Illustration 2 g01152578
Pin locations on ECM connector
(P1-31) Output 9 Test Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect ECM vehicle harness connector J1/P1, the firewall bulkhead connector, and the "Wait To Start Lamp". Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the wait to start lamp. Refer to Illustration 2.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for abrasion and pinch points from the battery to the ECM. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and the wiring is free of corrosion, of abrasion and of pinch points.Results:
Yes - The wiring is OK. Proceed to Test Step 2.
No - The wiring is not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check for Normal Operation of the Wait to Start Lamp
Connect Caterpillar Electronic Technician (ET). Access the configuration screen and ensure that the "Wait to Start Lamp" parameter is programmed to "J1/P1:31". Also, "Fast Idle Enabled Lamp" must be programmed to "J1/P1:21".
Turn the ignition key switch to the OFF/RESET position for ten seconds. Turn the ignition key switch to the ON position. Expected Result:The "Wait To Start Lamp" illuminates for approximately two seconds when the key switch is turned on. If conditions require the air inlet heater to turn on, the "Wait To Start Lamp" remains illuminated until the air inlet heater turns off or until the engine is started.Results:
Yes - The "Wait To Start Lamp" appears to operating correctly at this time.STOP
No - The "Wait To Start Lamp" is not operating correctly at this time. Proceed to Test Step 3.Test Step 3. Test the Circuit for the Wait to Start Lamp
Illustration 3 g01152582
Pin locations on ECM connector
(P1-31) Output 9
(P1-65) -Battery
Disconnect ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4
Illustration 1 g00770585
Circuit schematic for the wait to start lamp
Illustration 2 g01152578
Pin locations on ECM connector
(P1-31) Output 9 Test Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect ECM vehicle harness connector J1/P1, the firewall bulkhead connector, and the "Wait To Start Lamp". Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the wait to start lamp. Refer to Illustration 2.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for abrasion and pinch points from the battery to the ECM. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and the wiring is free of corrosion, of abrasion and of pinch points.Results:
Yes - The wiring is OK. Proceed to Test Step 2.
No - The wiring is not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check for Normal Operation of the Wait to Start Lamp
Connect Caterpillar Electronic Technician (ET). Access the configuration screen and ensure that the "Wait to Start Lamp" parameter is programmed to "J1/P1:31". Also, "Fast Idle Enabled Lamp" must be programmed to "J1/P1:21".
Turn the ignition key switch to the OFF/RESET position for ten seconds. Turn the ignition key switch to the ON position. Expected Result:The "Wait To Start Lamp" illuminates for approximately two seconds when the key switch is turned on. If conditions require the air inlet heater to turn on, the "Wait To Start Lamp" remains illuminated until the air inlet heater turns off or until the engine is started.Results:
Yes - The "Wait To Start Lamp" appears to operating correctly at this time.STOP
No - The "Wait To Start Lamp" is not operating correctly at this time. Proceed to Test Step 3.Test Step 3. Test the Circuit for the Wait to Start Lamp
Illustration 3 g01152582
Pin locations on ECM connector
(P1-31) Output 9
(P1-65) -Battery
Disconnect ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
318B, 320B, 320B FM LL, 320C FM, 320D, 321C, 321D LCR, 322B, 322B L, 322C, 322C FM, 324D FM, 324D FM LL
315B, 318B, 320 L, 320B, 320B FM LL, 320C, 320N, 325, 325B, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330B, 330B L, 330C FM, 330D FM, 568 FM LL, M325C MH, M325D L MH, W330B
315B, 318B, 320 L, 320B, 320B FM LL, 320B L, 322 FM L, 322B, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 325, 325B L, 325C FM, 325D FM, 325D FM LL, 330, M325B, M325C MH, M325D L MH
318B, 320 L, 320B, 320B FM LL, 320B L, 320C FM, 320D, 322 FM L, 322B, 322B L, 322B LN
311B, 311C, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321B, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
1190T, 1290T, 2391, 2491, 320 L, 320B, 320C, 320N, 322, 322 L, 322 LN, 322B, 322B L, 322C, 322C FM, 325, 325 L, 325 LN, 325B L, 325C, 325C L, 330, 330 FM L, 330 L, 330B, 522, 522B, 532, 552, 552 2, TK...
320B, 328D LCR
320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322B, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B, 325C, 325C L, 326D L, 328D LCR, 330C L, 375
320B, 320D, 322B, 325B, 375
320B, 320B FM LL, 320C FM, 320D, 322B, 325B, 375
318B, 318C, 319D L, 319D LN, 320, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 3...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 307B, 320C FM, 320D, 320D FM, 324D FM, 324D FM LL, 325D FM, 330D FM, 521B...
1661680
BUSHING
307B, 307C, 308C, 312C L
307B, 307C, 308C, 312C L
1686757
BUSHING-TRACK
307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E2 CR
307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E2 CR
1686756
BUSHING
307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
1531662
BUSHING
307B
307B
318B, 318C, 319D L, 319D LN, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 32...
1505848
BUSHING
318B
318B
318B, 318C, 319D L, 319D LN
318B, 320B, 320B L
318B, 320B, 320B L
1505819
BUSHING
318B
318B