2201012 BUSHING Caterpillar parts
420E, 420F, 432E, 434E
Rating:
Alternative (cross code) number:
CA2201012
220-1012
2201012
CA2201012
220-1012
2201012
Weight: 1 pounds 0 kg.
Information:
ID
70.329
mm
OD
83.135
mm
WIDTH
49
mm
BACKHOE LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Sunsong 2201012 Brake Hydraulic Hose
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Sunsong 2201012 Brake Hydraulic Hose
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Sunsong Each brake hose is precision engineered to exact fit and includes brackets, grommets, molded plastic guards, wire clips, and protective sleeves as required for to ensure that all wearable parts are restored to original condition || Brake hoses exceed DOT, Federal Vehicle Safety Standards (FMVSS 106) and SAE J1401 standards with a burst pressure rating of 8,700 psi, and a tensile strength of 560 lb. Durability test (Whip test) results exceed original equipment requirements by 300% || All tubing is manufactured from high grade steel and electroplated with a zinc coating (chromium III), delivering superior corrosion and rust resistance against elements such as high humidity, road salt, water, and grime || Every brake hose is subjected to a high pressure quality assurance test before leaving the factory, ensuring trouble free installation and operation of your new hose || Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Number on catalog scheme:
2B
For full view, you need register
Information:
D334, D336, D342, 1674, 1676The charts on the pages that follow list the contents of each tool group and the individual tool component usage by engine model. Some earlier model engines may require a conversion group to adapt them for use of lip-type seals. See pages 2 and 3.Converting Earlier Models To Use Lip-Type Seals
A 5S3903 Lip-Type Seal and new baffle can be installed on 631C (67M1-67M3695, 67M3697, 67M3699, 67M3706), 633C (66M1-66M638, 66M641) and 769B (99F1-99F2540, 99F2542, 99F2543, 99F2548) machines, provided they were originally equipped with the parts shown in the left illustration above and the sealing surface of the crankshaft is clean, smooth and capable of providing a good surface for the seal lip. Remove the former baffle, thrower and seal ring and install the new 5S3903 Seal and 1P4429 Baffle. An 8S3293 Seal Assembly can be installed on the following engines if equipped with a thrower and piston ring-type seal; D336 - 55B, 60B; 1676 - 54B; D334 - 92B, 93B; 1674 - 94B. Remove the thrower, seal and baffle and install the new baffle, wear sleeve and seal.Installing Wear Sleeve And Seal
1 Install locator (1) to the end of the crankshaft; tighten bolts (2) enough to hold the locator and yet allow some side movement. Place the wear sleeve on locator (1) with the outside angle toward the rear of the engine. Slide the sleeve onto the crankshaft to center locator (1), then tighten bolts (2). 2 Place sleeve installer ring (3) on plate (4), and place this assembly onto the stud of locator (1). Lubricate nut (5) and press the sleeve onto the crankshaft. Remove plate (4) and installer ring (3).
Start the sleeve straight on locator (1); if it is necessary to tap, use a soft hammer.
3 Lightly lubricate the seal with engine oil on the inside diameter and seal pilot (6), if required, on the outside diameter. If a wear sleeve is used, place the seal onto seal pilot (6), with the lip toward the crankcase. Slide pilot (6) onto locator (1) and the crankshaft or the gear, until the pilot bevel overlaps the sleeve bevel. 4 Place seal installer ring (7) on push plate (4) and place this assembly onto the stud of locator (1), or use bolt (2) and washer (8). Lubricate nut (5) or bolt (2) and press the seal into the flywheel housing or the baffle until the pusher plate becomes solid, or the shoulder on the installer ring stops against the flywheel housing or the baffle.Crankshaft Front Wear Sleeve And Seal Installation Tool Chart
Crankshaft Rear Wear Sleeve And Seal Installation Tool Chart
Bolt Identification And Size
A 5S3903 Lip-Type Seal and new baffle can be installed on 631C (67M1-67M3695, 67M3697, 67M3699, 67M3706), 633C (66M1-66M638, 66M641) and 769B (99F1-99F2540, 99F2542, 99F2543, 99F2548) machines, provided they were originally equipped with the parts shown in the left illustration above and the sealing surface of the crankshaft is clean, smooth and capable of providing a good surface for the seal lip. Remove the former baffle, thrower and seal ring and install the new 5S3903 Seal and 1P4429 Baffle. An 8S3293 Seal Assembly can be installed on the following engines if equipped with a thrower and piston ring-type seal; D336 - 55B, 60B; 1676 - 54B; D334 - 92B, 93B; 1674 - 94B. Remove the thrower, seal and baffle and install the new baffle, wear sleeve and seal.Installing Wear Sleeve And Seal
1 Install locator (1) to the end of the crankshaft; tighten bolts (2) enough to hold the locator and yet allow some side movement. Place the wear sleeve on locator (1) with the outside angle toward the rear of the engine. Slide the sleeve onto the crankshaft to center locator (1), then tighten bolts (2). 2 Place sleeve installer ring (3) on plate (4), and place this assembly onto the stud of locator (1). Lubricate nut (5) and press the sleeve onto the crankshaft. Remove plate (4) and installer ring (3).
Start the sleeve straight on locator (1); if it is necessary to tap, use a soft hammer.
3 Lightly lubricate the seal with engine oil on the inside diameter and seal pilot (6), if required, on the outside diameter. If a wear sleeve is used, place the seal onto seal pilot (6), with the lip toward the crankcase. Slide pilot (6) onto locator (1) and the crankshaft or the gear, until the pilot bevel overlaps the sleeve bevel. 4 Place seal installer ring (7) on push plate (4) and place this assembly onto the stud of locator (1), or use bolt (2) and washer (8). Lubricate nut (5) or bolt (2) and press the seal into the flywheel housing or the baffle until the pusher plate becomes solid, or the shoulder on the installer ring stops against the flywheel housing or the baffle.Crankshaft Front Wear Sleeve And Seal Installation Tool Chart
Crankshaft Rear Wear Sleeve And Seal Installation Tool Chart
Bolt Identification And Size
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 446D, 450E, 450F, 517, 527
414E, 416E, 416F, 420E, 420F, 422E, 422F, 424B, 424B HD, 428E, 428F, 430E, 430F, 432E, 432F, 442E, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-68B, CP-74B, CS-423E, CS-433E, CS-44, CS-5...
416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
416E, 416F, 420E, 420F, 422E, 428E, 432E, 434E
416E, 416F, 420E, 420F, 422E, 428E, 432E, 434E
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E, 450E, 450F
420E, 420F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
420E, 420F, 432E, 434E, 450E, 517, 527
420E, 420F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
416F, 420F, 422F, 428F, 430F, 432F, 938K
120M, 120M 2, 12M, 2384C, 2470C, 2484C, 2570C, 2670C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D...
420E, 420F, 432E, 434E, 450E, 517, 527
420E, 420F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
2061853
BUSHING
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F
2761368
BUSHING
307D, 308D, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F
307D, 308D, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E, 450E, 450F
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E
2171460
BUSHING
430E, 430F
430E, 430F
430E, 430F, 434E, 442E, 444E
2176046
BUSHING
430E, 430F
430E, 430F
430E, 430F, 442E, 444E
3229502
BUSHING-SPRING
416E, 422E, 422F, 428E, 428F, 434E
416E, 422E, 422F, 428E, 428F, 434E
420E, 420F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F