2227993 BUSHING Caterpillar parts
330C MH, 330D, 330D L, 330D MH, 336D L, 336D LN, 336E HVG
Rating:
Alternative (cross code) number:
CA2227993
222-7993
2227993
CA2227993
222-7993
2227993
Weight: 6 pounds 2 kg.
Information:
ID
110.3
mm
OD
130.24
mm
WIDTH
100
mm
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 2227993:
Number on catalog scheme:
13A
For full view, you need register
Information:
Probable Causes
Batteries
Battery cables
Starting circuit
Starting motor solenoid
Starting motor
Shutdown switch
Prelubrication system (if applicable)
Faulty crank enable switch (if applicable)
Flywheel ring gear
Transmission (if applicable)
Engine accessories
Hydraulic cylinder lock
Internal engine problemRecommended Actions
Batteries and/or Battery Cables
Inspect the main power switch, battery posts, and battery cables for loose connections and for corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Tighten any loose connections.
Inspect the batteries.
Charge the batteries. Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
Load test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries". Starting Motor Solenoid or Starting Circuit
Check the operation of the engine start switch. Monitor the engine start switch on Caterpillar Electronic Technician (ET). Refer to the appropriate troubleshooting test that is applicable to your engine if repairs are required.
Test the operation of the starting motor solenoid.
Check the wiring to the starting motor solenoid. Starting Motor or Flywheel Ring Gear
Test the operation of the starting motor.
Inspect the solenoid on the starter and the flywheel ring gear for damage. Prelubrication System (if applicable)
If equipped, inspect the prelubrication system for proper operation.Shutdown Switch
Use Cat ET to monitor the status of the engine. Check the status of engine shutdowns that are "ACTIVE" due to shutdown switches. Determine the cause for the engine shutdown and take the necessary action in order to resolve the shutdown.Crank Enable Switch (if applicable)
Ensure that the crank enable switch is not faulty.Transmission or Engine Accessories (if applicable)
If the engine's application has a transmission neutral switch, test the operation of the transmission neutral switch. Ensure that the machine is in neutral gear before attempting to start the engine.
Ensure free movement of the driveline.
Ensure that the timing pin was not left in the flywheel housing.
Remove any engine accessories that may lock up the engine and inspect any engine accessories that may lock up the engine. The following list illustrates examples of engine accessories that may lock up the engine:
Hydraulic pump that is driven from the rear gear group
Air compressor
Engine oil pump
Other components that are driven by the engineHydraulic Cylinder Lock
Check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors.Note: Drain the fuel from the cylinder head. Fuel will flow from the cylinder head into the cylinders when the unit injector is removed.Internal Engine Problem
Disassemble the engine. Refer to the Disassembly and Assembly manual. Inspect the internal components for the following conditions:
Seizure
Broken components
Bent components
Batteries
Battery cables
Starting circuit
Starting motor solenoid
Starting motor
Shutdown switch
Prelubrication system (if applicable)
Faulty crank enable switch (if applicable)
Flywheel ring gear
Transmission (if applicable)
Engine accessories
Hydraulic cylinder lock
Internal engine problemRecommended Actions
Batteries and/or Battery Cables
Inspect the main power switch, battery posts, and battery cables for loose connections and for corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Tighten any loose connections.
Inspect the batteries.
Charge the batteries. Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
Load test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries". Starting Motor Solenoid or Starting Circuit
Check the operation of the engine start switch. Monitor the engine start switch on Caterpillar Electronic Technician (ET). Refer to the appropriate troubleshooting test that is applicable to your engine if repairs are required.
Test the operation of the starting motor solenoid.
Check the wiring to the starting motor solenoid. Starting Motor or Flywheel Ring Gear
Test the operation of the starting motor.
Inspect the solenoid on the starter and the flywheel ring gear for damage. Prelubrication System (if applicable)
If equipped, inspect the prelubrication system for proper operation.Shutdown Switch
Use Cat ET to monitor the status of the engine. Check the status of engine shutdowns that are "ACTIVE" due to shutdown switches. Determine the cause for the engine shutdown and take the necessary action in order to resolve the shutdown.Crank Enable Switch (if applicable)
Ensure that the crank enable switch is not faulty.Transmission or Engine Accessories (if applicable)
If the engine's application has a transmission neutral switch, test the operation of the transmission neutral switch. Ensure that the machine is in neutral gear before attempting to start the engine.
Ensure free movement of the driveline.
Ensure that the timing pin was not left in the flywheel housing.
Remove any engine accessories that may lock up the engine and inspect any engine accessories that may lock up the engine. The following list illustrates examples of engine accessories that may lock up the engine:
Hydraulic pump that is driven from the rear gear group
Air compressor
Engine oil pump
Other components that are driven by the engineHydraulic Cylinder Lock
Check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors.Note: Drain the fuel from the cylinder head. Fuel will flow from the cylinder head into the cylinders when the unit injector is removed.Internal Engine Problem
Disassemble the engine. Refer to the Disassembly and Assembly manual. Inspect the internal components for the following conditions:
Seizure
Broken components
Bent components
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
322C, 322C FM, 325C, 325C FM, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 528, 657G, 824C, 826C, 834B, 834G, 834H, ...
1390, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E LN, 325B L, 325C, 325C ...
1390, 2590, 320B, 320C, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, ...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, ...
324D, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 329D LN, 330, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336...
320C, 324D, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330D, 330D FM, 330D L, 330D L...
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C ...
324D, 325D L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 385C L, 568 FM LL
330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345C MH, 3...
322B LN, 322C, 324D, 325B L, 325C, 325D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336E L, 340D L, 385C L
321C, 321D LCR, 322B LN, 322C, 325C, 325C FM, 325D L, 328D LCR, 330C, 330C L, 330D L, 345B II, 345C L, 365B II, 365C, 365C L, 385B, 385C L
324D, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 34...
2161553
BUSHING
330D, 349D L
330D, 349D L
2343811
BUSHING
325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN
325C, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN
2822984
BUSHING
G107B
G107B
2822961
BUSHING
G107B
G107B
2797388
BUSHING
G107B
G107B
2797386
BUSHING
G107B
G107B
3634226
BUSHING
GSH22B
GSH22B
3634227
BUSHING
GSH22B
GSH22B
3931643
BUSHING
CWAC-40
CWAC-40
4169512
BUSHING
CWAC-40
CWAC-40
3857322
BUSHING
CWAC-40
CWAC-40
3857981
BUSHING
CWAC-40
CWAC-40