2266052 BUSHING Caterpillar parts
773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777C, 777D, 777F, 777G, 844H, 844K, 854K, 990H, 990K, 992K, 993K, AD55B, AD60, C27, C32, D10N, D10R, D10T, D10T2, D11R, D11T, TH48-E70
Rating:
Alternative (cross code) number:
CA2266052
226-6052
2266052
CA2266052
226-6052
2266052
Weight: 1 pounds 0 kg.
GENERATOR SET, WHEEL LOADER,
Compatible equipment models: 2266052:
Information:
Which Generate This Code:MID 087 - Chassis ECMCID 1428 - Requested Gear Command SignalFMI 04 - Voltage Below NormalThis diagnostic code indicates the Chassis ECM detects the requested gear command is shorted to ground. The command signal circuit is a single wire that connects the Chassis ECM to the Drivetrain ECM. The signal wire is (J882-BR) is connected to contact J2-19 of the chassis ECM and contact J2-24 of the drivetrain ECM.Test Step 1. CHECK FOR A SHORT TO GROUND
Turn off the keyswitch and the disconnect switch.
Disconnect the J1 harness connector from the Chassis ECM.
Disconnect the J1 harness connector from the Drivetrain ECM.
At the J1 harness connector for the Chassis ECM, measure the resistance from contact J2-19 (wire J882-BR) to all the following sources of ground:
J1-13
J1-23
J1-56
J1-57
J1-70
J2-23
J2-63
Frame groundExpected Result:Each resistance is greater than 5000 ohms.Results:
OK - Each resistance is greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - A resistance is less than 5000 ohms. There is a short in the circuit with low resistance. Repair: Repair or replace the harness.STOPTest Step 2. CHECK THE HARNESSThe keyswitch and the disconnect switch remain off.
Inspect the harness.Clean and inspect the harness connector contacts for corrosion or damage. Check the wire insulation for damage caused by heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each circuit wire.
Reconnect all harness connectors. Verify that the connectors are fully seated and the clips are fastened.
Check for intermittent problems. Use Caterpillar® Electronic Technician (Cat® ET) to perform a wiggle test on the harness.
Turn on the disconnect switch and the keyswitch.
Operate the machine.
Determine if CID 1428 FMI 04 is active.Expected Result:CID 1428 FMI 04 is not active.Results:
OK - CID 1428 FMI 04 is not active. Repair: The initial diagnostic code was probably caused by a poor connection at one of the connectors that was checked. Resume normal operation.STOP
NOT OK - CID 1428 FMI 04 is active. Repair: Exit this procedure and perform this procedure again. Contact the technical communicator at your Cat® dealer. If the ECM requires replacement, see Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Turn off the keyswitch and the disconnect switch.
Disconnect the J1 harness connector from the Chassis ECM.
Disconnect the J1 harness connector from the Drivetrain ECM.
At the J1 harness connector for the Chassis ECM, measure the resistance from contact J2-19 (wire J882-BR) to all the following sources of ground:
J1-13
J1-23
J1-56
J1-57
J1-70
J2-23
J2-63
Frame groundExpected Result:Each resistance is greater than 5000 ohms.Results:
OK - Each resistance is greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - A resistance is less than 5000 ohms. There is a short in the circuit with low resistance. Repair: Repair or replace the harness.STOPTest Step 2. CHECK THE HARNESSThe keyswitch and the disconnect switch remain off.
Inspect the harness.Clean and inspect the harness connector contacts for corrosion or damage. Check the wire insulation for damage caused by heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each circuit wire.
Reconnect all harness connectors. Verify that the connectors are fully seated and the clips are fastened.
Check for intermittent problems. Use Caterpillar® Electronic Technician (Cat® ET) to perform a wiggle test on the harness.
Turn on the disconnect switch and the keyswitch.
Operate the machine.
Determine if CID 1428 FMI 04 is active.Expected Result:CID 1428 FMI 04 is not active.Results:
OK - CID 1428 FMI 04 is not active. Repair: The initial diagnostic code was probably caused by a poor connection at one of the connectors that was checked. Resume normal operation.STOP
NOT OK - CID 1428 FMI 04 is active. Repair: Exit this procedure and perform this procedure again. Contact the technical communicator at your Cat® dealer. If the ECM requires replacement, see Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Cat SIS web machinery list:
Parts bushing Caterpillar catalog:
8X6730
BUSHING
69D, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
69D, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
3U4680
BUSHING-RUBBER
740, 740B, AD40, AD45, AD55, AD55B, AD60, AE40, AE40 II, D25C, D25D, D30C, D350C, D350E, D350E II, D35C, D35HP, D400, D400E, D400E II, D40D, D44B, D550B, R2900
740, 740B, AD40, AD45, AD55, AD55B, AD60, AE40, AE40 II, D25C, D25D, D30C, D350C, D350E, D350E II, D35C, D35HP, D400, D400E, D400E II, D40D, D44B, D550B, R2900
7T7190
BUSHING
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
1J2192
BUSHING
824G II, 824H, 844, 844H, 854G, 854K, D10N, D10R, D10T, D10T2, D11N, D11R, D11T
824G II, 824H, 844, 844H, 854G, 854K, D10N, D10R, D10T, D10T2, D11N, D11R, D11T
1294487
BUSHING
D11N, D11R, D11T
D11N, D11R, D11T
9J1175
BUSHING
10, D10, D11N, D11R, D11T, D9L
10, D10, D11N, D11R, D11T, D9L
1458737
BUSHING
D11R, D11T
D11R, D11T
3T8458
BUSHING
D11N, D11R, D11T
D11N, D11R, D11T
9J1914
BUSHING
10, D10, D11N, D11R, D11T
10, D10, D11N, D11R, D11T
3T1378
BUSHING-SPHERICAL
D10N, D9L
D10N, D9L
9W9551
BUSHING
D10N, D10R, D10T
D10N, D10R, D10T
7T4134
BUSHING
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
3173717
BUSHING
3512, 3512B, 3512C, C27, C32
3512, 3512B, 3512C, C27, C32
5L2894
BUSHING
D379A, D379B, D398A, D398B, D399, G379, G398, G399
D379A, D379B, D398A, D398B, D399, G379, G398, G399
8N2275
BUSHING
D379B, D398, D9H, G398, G399
D379B, D398, D9H, G398, G399
2299780
BUSHING
C18, C32, C7
C18, C32, C7
2545887
BUSHING
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20
3072403
BUSHING
793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20
793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, C175-16, C175-20
3836312
BUSHING
C140-16
C140-16
3508860
BUSHING
C140-16
C140-16
3856067
BUSHING
C140-16
C140-16
3524538
BUSHING
C140-16
C140-16
3810847
BUSHING
C140-16
C140-16
3706545
BUSHING-CAMSHAFT
120M 2, 2384C, 2484C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 573C, 579C, 924K, 930K, 938K, 950K, 962K, BG1...
120M 2, 2384C, 2484C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 573C, 579C, 924K, 930K, 938K, 950K, 962K, BG1...