2276908 BUSHING Caterpillar parts
320C, 325C, 325C FM, 325D
Rating:
Alternative (cross code) number:
CA2276908
227-6908
2276908
CA2276908
227-6908
2276908
Weight: 4 pounds 2 kg.
Information:
ID
100.18
mm
OD
116.15
mm
WIDTH
100
mm
EXCAVATOR,
Related part:
2276908
BEARING-SLV-YM
5263043
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement for fits 2276908 Bearing-SL Fits Caterpillar 320C 325C 325C L 325D
Morricho Replacement for fits 2276908 Bearing-SL Fits Caterpillar 320C 325C 325C L 325D || Safety Assurance - parts give you peace of mind that your equipment remains safe to use || Manufacturer Warranty:1 Year || High Quality || Most items are 1 packs, unless specifically stated that it is a 2 pack.
Morricho Replacement for fits 2276908 Bearing-SL Fits Caterpillar 320C 325C 325C L 325D || Safety Assurance - parts give you peace of mind that your equipment remains safe to use || Manufacturer Warranty:1 Year || High Quality || Most items are 1 packs, unless specifically stated that it is a 2 pack.
2276908 BRG Sleeve (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 5.5 lbs || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 5.5 lbs || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
2276908 BRG Sleeve (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 5.5 lbs || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 5.5 lbs || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
Number on catalog scheme:
9A
For full view, you need register
Information:
Use this procedure in order to troubleshoot the following event codes.
Table 1
Event Code
Description Conditions which Activate the Code System Response
E229 (1) Fuel Energy Content Set Too Low The fuel correction factor is less than the trip point for 20 seconds. The alarm output is activated. The code is logged.
E230 (1) Fuel Energy Content Set Too High The fuel correction factor is greater than the trip point for 20 seconds.
E231 (3) Fuel Quality Out of Range The actual BTU of the fuel has exceeded the acceptable range. The shutdown output is activated. The code is logged. The engine is shut down. Note: Within the configuration screen for the master ECM, there are four parameters that relate to the fuel quality:
"Fuel Quality Input Type Configuration"
"Fuel Quality Sensor LHV Lower Limit"
"Fuel Quality Sensor LHV Upper Limit"
"Fuel Quality"Be sure that the configuration parameter for "Fuel Quality Input Type Configuration" is set for the proper system.When the "Fuel Quality Input Type Configuration" parameter is set to "Configuration" a fixed value must be set for the "Fuel Quality" parameter. Engines that run on a consistent fuel supply typically use this type of system.When the "Fuel Quality Input Type Configuration" parameter is set to "4-20mA" a variable value is used by the software. The "4-20mA" signal is provided by the customer via a sensor that measures fuel quality. For this system, set the "Fuel Quality Sensor LHV Lower Limit" to the value that corresponds to the "4mA" signal and set the "Fuel Quality Sensor LHV Upper Limit" to the value that corresponds to the "20mA" signal. Engines that run on a inconsistent fuel supply typically use this type of system. Engines that run on gas from a coal seam or landfill are examples of an inconsistent fuel supply.Probable Causes
The Low Heat Value (LHV) of the gas or the specific gravity of the gas is significantly different from the value that is programmed into the electronic control module.
Condensation is forming in the gas.Recommended Repairs
Obtain a Fuel Analysis and Program the "Fuel Quality" Parameter
Obtain an analysis of the gas in order to determine the LHV. Program the "Fuel Quality" parameter to the actual value of the LHV.If the quality of the gas is not consistent, obtain several analyses over a period of time. Program the "Fuel Quality" parameter to the average value of the LHV.Check the Dryer for the Gas
Check the dryer for the gas for proper operation. Repair the dryer, if necessary.
Table 1
Event Code
Description Conditions which Activate the Code System Response
E229 (1) Fuel Energy Content Set Too Low The fuel correction factor is less than the trip point for 20 seconds. The alarm output is activated. The code is logged.
E230 (1) Fuel Energy Content Set Too High The fuel correction factor is greater than the trip point for 20 seconds.
E231 (3) Fuel Quality Out of Range The actual BTU of the fuel has exceeded the acceptable range. The shutdown output is activated. The code is logged. The engine is shut down. Note: Within the configuration screen for the master ECM, there are four parameters that relate to the fuel quality:
"Fuel Quality Input Type Configuration"
"Fuel Quality Sensor LHV Lower Limit"
"Fuel Quality Sensor LHV Upper Limit"
"Fuel Quality"Be sure that the configuration parameter for "Fuel Quality Input Type Configuration" is set for the proper system.When the "Fuel Quality Input Type Configuration" parameter is set to "Configuration" a fixed value must be set for the "Fuel Quality" parameter. Engines that run on a consistent fuel supply typically use this type of system.When the "Fuel Quality Input Type Configuration" parameter is set to "4-20mA" a variable value is used by the software. The "4-20mA" signal is provided by the customer via a sensor that measures fuel quality. For this system, set the "Fuel Quality Sensor LHV Lower Limit" to the value that corresponds to the "4mA" signal and set the "Fuel Quality Sensor LHV Upper Limit" to the value that corresponds to the "20mA" signal. Engines that run on a inconsistent fuel supply typically use this type of system. Engines that run on gas from a coal seam or landfill are examples of an inconsistent fuel supply.Probable Causes
The Low Heat Value (LHV) of the gas or the specific gravity of the gas is significantly different from the value that is programmed into the electronic control module.
Condensation is forming in the gas.Recommended Repairs
Obtain a Fuel Analysis and Program the "Fuel Quality" Parameter
Obtain an analysis of the gas in order to determine the LHV. Program the "Fuel Quality" parameter to the actual value of the LHV.If the quality of the gas is not consistent, obtain several analyses over a period of time. Program the "Fuel Quality" parameter to the average value of the LHV.Check the Dryer for the Gas
Check the dryer for the gas for proper operation. Repair the dryer, if necessary.
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
322C, 325C
322C, 325C, 330C, 330C FM, 330C L, 385B, 385C L
322C, 325C, 330C, 330C FM, 330C L, 385B, 385C L
321C, 322C, 325C, 330C, 330C FM, 330C L, 385B
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365C, W345C MH
325C, 330C, 330C FM, 330C L, 330D L
325C
325C FM, 325D FM, 325D FM LL, 330 L, 330B, 330B L, M325C MH, M325D L MH
325C, 325C FM
325D, 325D FM, 325D L, 329D, 329D L, 329D LN
1865025
BUSHING
550B, 560B, 570B, 580B
550B, 560B, 570B, 580B
2442349
BUSHING
564
564
2251005
BUSHING
554, 564, 574B
554, 564, 574B
2129962
BUSHING AS
HH44 DE, HH45, HH500, HH55, HH65, HH75
HH44 DE, HH45, HH500, HH55, HH65, HH75
2102657
BUSHING
320C, 320D FM, HF181, HF221
320C, 320D FM, HF181, HF221
2266332
BUSHING
320C, 320D FM, 543, HF181, HF201, HF201B, HF202, HF221, HF222, SC-57, SH-56B, SS-56
320C, 320D FM, 543, HF181, HF201, HF201B, HF202, HF221, HF222, SC-57, SH-56B, SS-56
2611015
BUSHING-TRACK
1090, 2290, 324D FM, 511, TK711
1090, 2290, 324D FM, 511, TK711
2611016
BUSHING-MASTER
1090, 2290, 324D FM, 511, TK711
1090, 2290, 324D FM, 511, TK711
1190T, 1290T, 2391, 2491, 320, 320 L, 320N, 522, 522B, 532, 552, 552 2, E200B, TK722, TK732, TK752
2192458
BUSHING
1190T, 1290T, 2391, 2491, 522, 522B, 532, 552, 552 2, TK722, TK732, TK752
1190T, 1290T, 2391, 2491, 522, 522B, 532, 552, 552 2, TK722, TK732, TK752
2342994
BUSHING
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
2237075
BUSHING-FLANGE
321C, 328D LCR
321C, 328D LCR