2789255 BUSHING Caterpillar parts
324D, 324D L, 326D L
Rating:
Alternative (cross code) number:
CA2789255
278-9255
2789255
CA2789255
278-9255
2789255
Weight: 4 pounds 1 kg.
EXCAVATOR,
Related part:
2789255
BEARING-SLV-YM
5263053
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing (30x45x35)
Generic Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing
Generic Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing
Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing (35x45x45)
Generic Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing
Generic Compatible with E336D2L/336GC 278-9255 241-7341 Point Alloy Copper Sleeve Excavator Bushing
$175.00
30 Nov 2022
US: NY Heavy Tracto
Caterpillar 2789255 278-9255 Bearing X2 Replacement Cat Caterpillar Boom 315B 315C 315Cl
Caterpillar
Caterpillar
Number on catalog scheme:
11A
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B - Guide Stud
(M10 x 1.25 mm by 80mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 1 g01305341
Typical example
If the ring gear was removed, follow Steps 1.a through 1.c in order to install ring gear (3) to flywheel (2).
Identify the orientation of the new ring gear in order to install the ring gear correctly onto the flywheel. Note: The chamfered side of gear teeth (Y) must face toward the starting motor when the flywheel is installed. This will ensure the correct engagement of the starting motor.
Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (2).
Illustration 2 g01305297
Typical example
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install".
Install Tooling (B) to positions (X) in the crankshaft.
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Position flywheel (2) onto Tooling (B). On three cylinder engines that have a roll pin, ensure that the roll pin is installed to the crankshaft and that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (B) and install the two remaining bolts (1).
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft).
Remove Tooling (A) and the lifting device from the flywheel. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B - Guide Stud
(M10 x 1.25 mm by 80mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 1 g01305341
Typical example
If the ring gear was removed, follow Steps 1.a through 1.c in order to install ring gear (3) to flywheel (2).
Identify the orientation of the new ring gear in order to install the ring gear correctly onto the flywheel. Note: The chamfered side of gear teeth (Y) must face toward the starting motor when the flywheel is installed. This will ensure the correct engagement of the starting motor.
Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (2).
Illustration 2 g01305297
Typical example
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install".
Install Tooling (B) to positions (X) in the crankshaft.
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Position flywheel (2) onto Tooling (B). On three cylinder engines that have a roll pin, ensure that the roll pin is installed to the crankshaft and that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (B) and install the two remaining bolts (1).
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft).
Remove Tooling (A) and the lifting device from the flywheel. End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
1390, 2590, 320B, 320C, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, ...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, ...
324D, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 329D LN, 330, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336...
320C, 324D, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330D, 330D FM, 330D L, 330D L...
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C ...
324D, 325D L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 385C L, 568 FM LL
322B LN, 322C, 324D, 325B L, 325C, 325D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336E L, 340D L, 385C L
320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322B, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B, 325C, 325C L, 326D L, 328D LCR, 330C L, 375
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
324D, 324D FM, 324D L, 324D LN, 326D L
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
324D, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 34...
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
2542035
BUSHING
M322C, M322D, M322D MH
M322C, M322D, M322D MH
2462645
BUSHING
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
2611015
BUSHING-TRACK
1090, 2290, 324D FM, 511, TK711
1090, 2290, 324D FM, 511, TK711
2611016
BUSHING-MASTER
1090, 2290, 324D FM, 511, TK711
1090, 2290, 324D FM, 511, TK711
1190T, 1290T, 2391, 2491, 320, 320 L, 320N, 522, 522B, 532, 552, 552 2, E200B, TK722, TK732, TK752
8E6095
BUSHING-TRACK
345B, 345C, 350, 350 L
345B, 345C, 350, 350 L
324D, 324D FM, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E
324D, 324D FM, 324D L, 324D LN, 326D L
3575712
BUSHING
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L, 324D
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L, 324D
320D, 320D L, 320D2, 320D2 L, 320E LN, 323D L, 323D2 L, 323E L, 324D, 324D L, 324E, 324E L, 324E LN, 325D L, 326D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
2909181
BUSHING
324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 326D L, 329D, 329D L, 329E, 329E L, 329E LN
324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 326D L, 329D, 329D L, 329E, 329E L, 329E LN