3575717 BUSHING Caterpillar parts
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
Rating:
Alternative (cross code) number:
CA3575717
357-5717
3575717
CA3575717
357-5717
3575717
Weight: 2 pounds 1 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YNRSP 3575717 Sleeve Bearing for Heavy Equipment (2Pcs)
YNRSP Brand: YNRSP || Part Number: 3575717 || Part type: Sleeve Bearing || Weight: 2.97 lbs (1.35 kg) || Easy in-and-out fit
YNRSP Brand: YNRSP || Part Number: 3575717 || Part type: Sleeve Bearing || Weight: 2.97 lbs (1.35 kg) || Easy in-and-out fit
Number on catalog scheme:
1A
For full view, you need register
Compatible equipment models: 3575717:
Information:
This diagnostic code becomes active when all of the parameters for the CAN data link for the object detection sensor are missing for more than 250 milliseconds. This diagnostic code is associated with the wire harnesses that connect to the components for the object detection system. Failure of the internal CAN data link wiring of an object detection component may also cause this diagnostic code. This failure causes the data link communications to be disrupted.Note: For Off-Highway Trucks, this code corresponds with the front object detection sensor.System Response:The object detection system is disabled. The system will reactivate when all of the parameters on the CAN data link are available. The status indicator for the system will illuminate red.Test Step 1. CYCLE THE POWER TO THE SYSTEM
Place the key start switch and the disconnect switch in the OFF position.
Turn the disconnect switch and the key start switch to the ON position.
Check the status of the diagnostic code MID 134 – CID 3319 – FMI 09. Expected Result:The diagnostic code is not active.Results:
YES - The diagnostic code is not active.Repair: The diagnostic code was caused by the internal wiring for the CAN data link of the display. Cycling the power to the system has reset the display. Return the machine to normal operation.STOP
NO - The diagnostic code is still active. Proceed to Test Step 2.Test Step 2. CHECK POWER TO THE OBJECT DETECTION SENSOR
Disconnect the connector from the object detection sensor.
Take the following measurement at the harness connector for the object detection sensor. Measure the voltage between contact 4 wire (C569-YL(Yellow)) and contact 1 wire (C234-BK(Black)). Expected Result:The voltage measurement is 12 3 VDC.Results:
YES - The voltage measurements are 12 3 VDC. Proceed to Test Step 3.
NO - The voltage measurements are NOT 12 3 VDC.Repair: The 12/24 V power converter has failed or the machines charging system is not functioning correctly. Replace the 12/24 V power converter or repair the charging system.STOPTest Step 3. CHECK THE RESISTANCE OF THE CAN DATA LINK
Place the key start switch and the disconnect switch in the OFF position.
Disconnect connector "CM-C1" from the back of the display.
Take the following measurement at the "CM-C1" connector that is located in the center on the back of the display. Measure the resistance between contact 7 wire (K900-YL(Yellow)) and contact 8 wire (K990-GN(Green)). Note the resistances. Expected Result:The resistance measurement is 60 6 ohms.Results:
YES - The resistance measurement is 60 6 ohms. Proceed to Test Step 5.
NO - The resistance measurement is NOT 60 6 ohms. Proceed to Test Step 4.Test Step 4. CHECK THE TERMINATION RESISTOR
Disconnect the 3-pin connector for both of the termination resistors.
Measure the resistance across contact A and contact B for one resistor. Measure the resistance across contact A and contact B for the other resistor. Note the resistance. Expected Result:The resistance measurements are 120 12 ohms for each resistor.Results:
YES - The resistance measurements are 120 12 ohms. Reconnect the resistors. Proceed to Test Step 5.
NO
Place the key start switch and the disconnect switch in the OFF position.
Turn the disconnect switch and the key start switch to the ON position.
Check the status of the diagnostic code MID 134 – CID 3319 – FMI 09. Expected Result:The diagnostic code is not active.Results:
YES - The diagnostic code is not active.Repair: The diagnostic code was caused by the internal wiring for the CAN data link of the display. Cycling the power to the system has reset the display. Return the machine to normal operation.STOP
NO - The diagnostic code is still active. Proceed to Test Step 2.Test Step 2. CHECK POWER TO THE OBJECT DETECTION SENSOR
Disconnect the connector from the object detection sensor.
Take the following measurement at the harness connector for the object detection sensor. Measure the voltage between contact 4 wire (C569-YL(Yellow)) and contact 1 wire (C234-BK(Black)). Expected Result:The voltage measurement is 12 3 VDC.Results:
YES - The voltage measurements are 12 3 VDC. Proceed to Test Step 3.
NO - The voltage measurements are NOT 12 3 VDC.Repair: The 12/24 V power converter has failed or the machines charging system is not functioning correctly. Replace the 12/24 V power converter or repair the charging system.STOPTest Step 3. CHECK THE RESISTANCE OF THE CAN DATA LINK
Place the key start switch and the disconnect switch in the OFF position.
Disconnect connector "CM-C1" from the back of the display.
Take the following measurement at the "CM-C1" connector that is located in the center on the back of the display. Measure the resistance between contact 7 wire (K900-YL(Yellow)) and contact 8 wire (K990-GN(Green)). Note the resistances. Expected Result:The resistance measurement is 60 6 ohms.Results:
YES - The resistance measurement is 60 6 ohms. Proceed to Test Step 5.
NO - The resistance measurement is NOT 60 6 ohms. Proceed to Test Step 4.Test Step 4. CHECK THE TERMINATION RESISTOR
Disconnect the 3-pin connector for both of the termination resistors.
Measure the resistance across contact A and contact B for one resistor. Measure the resistance across contact A and contact B for the other resistor. Note the resistance. Expected Result:The resistance measurements are 120 12 ohms for each resistor.Results:
YES - The resistance measurements are 120 12 ohms. Reconnect the resistors. Proceed to Test Step 5.
NO
Cat SIS web machinery list:
Parts bushing Caterpillar catalog:
318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322C, 322...
315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 3...
307D, 308D, 308E, 308E2 CR, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E...
315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322C, 323D L, 3...
315D L, 316E L, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 323D L, 323...
315D L, 316E L, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 32...
319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E...
319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D FM, 324D L, 324D LN, 325D, 325D FM,...
319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D FM, 324D L, 324D LN, 32...
314D CR, 314D LCR, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L
1390, 2590, 320 L, 320B, 320C, 320D, 320D FM, 320D2, 320D2 L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E LN, 325B L, 325C, 325C ...
321C, 321D LCR, 322B LN, 322C, 325C, 325C FM, 325D L, 328D LCR, 330C, 330C L, 330D L, 345B II, 345C L, 365B II, 365C, 365C L, 385B, 385C L
3620327
BUSHING
320D FM, HH44 DE
320D FM, HH44 DE
3620314
BUSHING
320D FM, HH44 DE
320D FM, HH44 DE
2085366
BUSHING
320D FM
320D FM
3169822
BUSHING
525C
525C
2705259
BUSHING-THRUST
525C, 535C, 545C
525C, 535C, 545C
3781593
BUSHING
525C, 525D, 535C, 535D, 545C, 545D, 555D
525C, 525D, 535C, 535D, 545C, 545D, 555D
3545363
BUSHING
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
3622876
BUSHING
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
3622874
BUSHING
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
3845480
BUSHING-TRACK
320D, 320D FM
320D, 320D FM
3890670
BUSHING-MASTER
320D, 320D FM
320D, 320D FM
3575711
BUSHING
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L
320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D2 L, 323E L