3852900 BUSHING Caterpillar parts
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318D L, 318D2 L, 318E L
Rating:
Alternative (cross code) number:
CA3852900
385-2900
3852900
CA3852900
385-2900
3852900
Weight: 0.33 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 3852900:
Number on catalog scheme:
5
For full view, you need register
Information:
System Operation Description:There are problems that could be reported by the Product LinkPL102C System but the problems are not caused by the Product LinkPL102C module. The following section describes the problems. This section contains steps that are used to determine the possible cause. The module, the antenna, and cables should be visually inspected for damage. Verify that there are no loose connections.Description of the Problem:Reports and messages are not received in the office.The Product LinkPL102C system depends on several communication links in order to transfer data from the machine to the office. The following procedures assume that these communication links are operating properly. The proper communication links are listed below:
The cellular network is operational in the geographic area of concern. The cellular coverage is confirmed by clicking the "Status" tab on the Caterpillar Service Tool software screen.
The worldwide network of Caterpillar's computers is passing messages to the Equipment Manager (EM) software.
EM is configured properly and the software is functioning.The Product LinkPL102C module should not be replaced without verifying that the issues mentioned have been investigated and resolved if needed. Contact the Service System Support Center for aid in resolving these issues.In "Power Mode 1", position and SMU reports are transmitted as scheduled in Caterpillar Service Tool. Fewer messages are sent in power mode 2 and power mode 3. If messages are not available in Equipment Manager, proceed with the following steps in order to determine the cause. Test Step 1. ACCESS THE PRODUCT LINK THROUGH CATERPILLAR SERVICE TOOL.
Connect Caterpillar Service Tool to the machine.
Verify that the Product LinkPL102C module is available.Expected Result:The Product LinkPL102C module is available.Results:
OK - The Product LinkPL102C module is available. Proceed to test step 2.
NOT OK - The Product LinkPL102C module is not present in the Caterpillar Service Tool screen. Repair: Verify that the wiring for the Product LinkPL102C module has been installed correctly. Refer to Special Instuction, REHS2143, "Confirm Wiring Harness Connections". Step 4 of the procedure in the "Confirm Wiring Harness Connections" section, checks the wiring with a multimeter. If the ECM (Product Link) is not available, refer to System Operation Troubleshooting Testing and Adjusting, RENR8115, "Electronic Service Tool Does Not Communicate with ECM". Stop.Test Step 2. VERIFY THAT THE PRODUCT LINK MODULE IS CONFIGURED PROPERLY.
In the Caterpillar Service Tool, go to the "Configuration" tab. See Testing and Adjusting, "Installation Parameters - Configure" for more information.
Verify that the "PLM Enable Status" is configured as "Enabled".
Verify that the "Dealer Identification Code" is configured with the correct code for the Dealer.
Verify that the "DBS Machine Make Code" is configured correctly.
Verify that the "Machine Serial Number" is configured with the correct machine serial number.Expected Result:All settings are correct.Results:
OK - The Product LinkPL102C module is configured correctly. Proceed to Test Step 3.
NOT OK - The Product LinkPL102C module is not configured correctly. Repair: Correct the configuration information of the Product LinkPL102C module. Click the "Configure" tab in Caterpillar Service Tool to access the configuration parameters. Verify the configuration using the "Status" tab in the Caterpillar Service
The cellular network is operational in the geographic area of concern. The cellular coverage is confirmed by clicking the "Status" tab on the Caterpillar Service Tool software screen.
The worldwide network of Caterpillar's computers is passing messages to the Equipment Manager (EM) software.
EM is configured properly and the software is functioning.The Product LinkPL102C module should not be replaced without verifying that the issues mentioned have been investigated and resolved if needed. Contact the Service System Support Center for aid in resolving these issues.In "Power Mode 1", position and SMU reports are transmitted as scheduled in Caterpillar Service Tool. Fewer messages are sent in power mode 2 and power mode 3. If messages are not available in Equipment Manager, proceed with the following steps in order to determine the cause. Test Step 1. ACCESS THE PRODUCT LINK THROUGH CATERPILLAR SERVICE TOOL.
Connect Caterpillar Service Tool to the machine.
Verify that the Product LinkPL102C module is available.Expected Result:The Product LinkPL102C module is available.Results:
OK - The Product LinkPL102C module is available. Proceed to test step 2.
NOT OK - The Product LinkPL102C module is not present in the Caterpillar Service Tool screen. Repair: Verify that the wiring for the Product LinkPL102C module has been installed correctly. Refer to Special Instuction, REHS2143, "Confirm Wiring Harness Connections". Step 4 of the procedure in the "Confirm Wiring Harness Connections" section, checks the wiring with a multimeter. If the ECM (Product Link) is not available, refer to System Operation Troubleshooting Testing and Adjusting, RENR8115, "Electronic Service Tool Does Not Communicate with ECM". Stop.Test Step 2. VERIFY THAT THE PRODUCT LINK MODULE IS CONFIGURED PROPERLY.
In the Caterpillar Service Tool, go to the "Configuration" tab. See Testing and Adjusting, "Installation Parameters - Configure" for more information.
Verify that the "PLM Enable Status" is configured as "Enabled".
Verify that the "Dealer Identification Code" is configured with the correct code for the Dealer.
Verify that the "DBS Machine Make Code" is configured correctly.
Verify that the "Machine Serial Number" is configured with the correct machine serial number.Expected Result:All settings are correct.Results:
OK - The Product LinkPL102C module is configured correctly. Proceed to Test Step 3.
NOT OK - The Product LinkPL102C module is not configured correctly. Repair: Correct the configuration information of the Product LinkPL102C module. Click the "Configure" tab in Caterpillar Service Tool to access the configuration parameters. Verify the configuration using the "Status" tab in the Caterpillar Service
Cat SIS web machinery list:
Parts bushing Caterpillar catalog:
318C, 318E L, 319C, 320B, 320C, 320D, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321B, 321C, 321D LCR, 322C, 323D L, 323D LN, 323D2 L, 323E L, 324D, 324D FM, ...
315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 3...
307D, 308D, 308E, 308E2 CR, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E...
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318D L, 318D2 L, 318E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E L...
315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322C, 323D L, 3...
315D L, 316E L, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 323D L, 323...
315D L, 316E L, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 32...
314D CR, 314D LCR, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L
312D2, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 5110B
312D2, 385B, 385C, 385C L, 385C L MH, 390D, 390D L, 390F L
312D2, 365B II, 365C, 365C L, 385B, 385C, 385C L, 390D, 390D L, 390F L
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
2185211
BUSHING
308D, 308E, 308E SR, 308E2 CR
308D, 308E, 308E SR, 308E2 CR
3211268
BUSHING-FLANGE
308D, 314D CR, 314D LCR, 321D LCR
308D, 314D CR, 314D LCR, 321D LCR
2969446
BUSHING
308D, 308E, 308E CR, 308E2 CR
308D, 308E, 308E CR, 308E2 CR
2457750
BUSHING-RUBBER
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
315D L, 316E L, 318D L, 318D2 L, 318E L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 323D L, 323...
315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 321D LCR, 322C, 323D L, 3...
3439331
BUSHING
315D L, 318D L
315D L, 318D L
3439329
BUSHING
315D L
315D L
3852934
BUSHING
315D L, 316E L, 318D L, 318D2 L, 318E L
315D L, 316E L, 318D L, 318D2 L, 318E L
314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318D L, 318D2 L, 318E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E L...