BUSHING 4504809 - Caterpillar

4504809 BUSHING Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4504809
450-4809
4504809

Weight: 3 pounds 1 kg.

Buy BUSHING 4504809 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Jmf Hose Barb Tee 3/8 " Hose Barb X 3/8 " Hose Barb X 3/8 " Yellow Brass 150 Psi Lead Free

$12.35

28 Nov 2022
0.2[0.09] Pounds
US: Team FTO Store

Jmf Hose Barb Tee 3/8 " Hose Barb X 3/8 " Hose Barb X 3/8 " Yellow Brass 150 Psi Lead Free
JMF Material: Brass || Product Type: Hose Barb || Inlet Diameter: 3/8 in. || Outlet Diameter: 3/8 in. || Compatibility: Plastic or Rubber Hose

$16.99

01 Jun 2021
1.0[0.45] Pounds
US: 303hobbysales

HOSE BARB TEE 3/8" LF
JMF

$10.80

18 Aug 2021
0.2[0.09] Pounds
US: Gatzies

Number on catalog scheme: 2

Caterpillar 4504809 Parts scheme BUSHING

For full view, you need register

Information:

Droop
This parameter allows the engine to operate in a load sharing system.
Table 16
Minimum Default Maximum
0.0 0.0 10 Fuel Position Multiplier
This parameter decreases the power output from the engine by reducing the fuel. This parameter is used to control the driven equipment. A decrease in engine power does not require a change in the throttle.
Table 17
Minimum Default Maximum
Disabled Disabled Enabled Engine Acceleration Rate
This parameter limits the rate of change for the desired engine speed. This parameter may also help reduce smoke when you start the engine.
Table 18
Minimum Default Maximum
1 rpm per second 250 rpm per second 2000 rpm per second Cooling Warning Engine Load Enable
This parameter is used to issue a warning to the operator that to much load has been added to the engine before the jacket water has reached the proper operating temperature of 75 °C (167 °F) or greater.
Table 19
Minimum Default Maximum
5% 40% 95% Throttle
The parameter is used to decide whether the continuous throttle or the multi-position throttle will be used. Table 21 defines notch speeds for a multi-position throttle.
Table 20
Minimum Default Maximum
Continuous Continuous Notch
Table 21
Notch Speed Number Percent Duty Cycle Minimum RPM Default RPM Maximum RPM
Idle <10 450 600 1900
1 <20 450 700 1900
2 <30 450 1300 1900
3 <40 450 1500 1900
4 <50 450 1600 1900
5 <60 450 1675 1900
6 <70 450 1715 1900
7 <80 450 1770 1900
8 <95 450 1800 1900 Injector Trim Code
Note: The injector trim code is not part of the "Configuration" screen on Caterpillar Electronic Technician (ET). "Injector Codes Calibration" can be found under "Calibrations" in the "Service" menu on Cat ET.The injector trim code is a number that is found on each of the unit injectors. The ECM uses this number to compensate for manufacturing variations between individual injectors. If you replace any of the unit injectors, you must reprogram the injector trim codes for the new injectors. Also, if you replace the ECM, you must reprogram all of the injector trim codes.
Table 22
Injector Trim Code
Injector Default Range Password
"Inj #1 e-trim" 0000 4 numeric characters No
"Inj #2 e-trim" 0000 4 numeric characters No
"Inj #3 e-trim" 0000 4 numeric characters No
"Inj #4 e-trim" 0000 4 numeric characters No
"Inj #5 e-trim" 0000 4 numeric characters No
"Inj #6 e-trim" 0000 4 numeric characters No
"Inj #7 e-trim" 0000 4 numeric characters No
"Inj #8 e-trim" 0000 4 numeric characters No
"Inj #9 e-trim" 0000 4 numeric characters No
"Inj #10 e-trim" 0000 4 numeric characters No
"Inj #11 e-trim" 0000 4 numeric characters No
"Inj #12 e-trim" 0000 4 numeric characters No
"Inj #13 e-trim" 0000 4 numeric characters No
"Inj #14 e-trim" 0000 4 numeric characters No
"Inj #15 e-trim" 0000 4 numeric characters No
"Inj #16 e-trim" 0000 4 numeric characters No