5I7542 BUSHING Caterpillar parts
311B, 311C, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321B, 321C, 323D L, 323D LN
Rating:
Alternative (cross code) number:
CA5I7542
5I-7542
5I7542
CA5I7542
5I-7542
5I7542
Weight: 0.010 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 5I7542:
Information:
Attach a "Do Not Operate" warning tag to the start switch or to the controls before the engine is serviced or repaired. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer. Attach the warning tags to the engine and to each operator control station. When appropriate, disconnect the starting controls.
Illustration 1 g00104545
Do not allow unauthorized personnel on the engine or around the engine when the engine is serviced.
Illustration 2 g00702020
Wear a hard hat, protective glasses, and other protective equipment, as required.
Tampering with the engine installation or tampering with the OEM supplied wiring can be dangerous. Personal injury, death and/or engine damage could result.
Vent the engine exhaust to the outside when the engine is operated in an enclosed area.
Do not release the secondary brake or the parking brake systems unless the vehicle is blocked or unless the vehicle is restrained.
When work is performed around an engine that is operating, wear protective devices for ears in order to help prevent damage to hearing.
Do not wear loose clothing or jewelry that can snag on controls or on other parts of the engine.
Ensure that all protective guards and all covers are secured in place on the engine.
Never put maintenance fluids into glass containers. Glass containers can break.
Use all cleaning solutions with care.
Report all necessary repairs.Unless other instructions are provided, perform the maintenance under the following conditions:
The engine is stopped. Ensure that the engine cannot be started.
The protective locks or the controls are in the applied position.
Engage the secondary brakes or parking brakes.
Block the vehicle or restrain the vehicle before maintenance or repairs are performed.
Disconnect the batteries when maintenance is performed or when the electrical system is serviced. Disconnect the battery ground leads. Tape the leads in order to help prevent sparks.
Disconnect the connector for the unit injector that is located on the valve cover base. This procedure will help prevent personal injury from the high voltage to the unit injectors. Do not come in contact with the unit injector terminals while the engine is operating.
Do not attempt any repairs or any adjustments to the engine while the engine is operating.
Do not attempt any repairs that are not understood. Use the proper tools. Replace any equipment that is damaged or repair the equipment.
When starting a new engine or an engine which has not been started since service has been performed, make provisions to stop the engine if an overspeed occurs. Shutting down the engine may be accomplished by shutting off the fuel supply and/or the air supply to the engine.
Start the engine from the operator station (cab). Never short across the starting motor terminals or the batteries which could bypass the engine neutral start system and/or the electrical system could be damaged.Cautiously remove the following parts:Note: To help prevent spraying or splashing of pressurized fluids, hold a rag over the part that is being removed.
Filler caps
Grease fittings
Pressure taps
Breathers
Drain plugsUse caution when cover plates are removed. Gradually loosen but do not remove the last two bolts or nuts that are located at opposite
Illustration 1 g00104545
Do not allow unauthorized personnel on the engine or around the engine when the engine is serviced.
Illustration 2 g00702020
Wear a hard hat, protective glasses, and other protective equipment, as required.
Tampering with the engine installation or tampering with the OEM supplied wiring can be dangerous. Personal injury, death and/or engine damage could result.
Vent the engine exhaust to the outside when the engine is operated in an enclosed area.
Do not release the secondary brake or the parking brake systems unless the vehicle is blocked or unless the vehicle is restrained.
When work is performed around an engine that is operating, wear protective devices for ears in order to help prevent damage to hearing.
Do not wear loose clothing or jewelry that can snag on controls or on other parts of the engine.
Ensure that all protective guards and all covers are secured in place on the engine.
Never put maintenance fluids into glass containers. Glass containers can break.
Use all cleaning solutions with care.
Report all necessary repairs.Unless other instructions are provided, perform the maintenance under the following conditions:
The engine is stopped. Ensure that the engine cannot be started.
The protective locks or the controls are in the applied position.
Engage the secondary brakes or parking brakes.
Block the vehicle or restrain the vehicle before maintenance or repairs are performed.
Disconnect the batteries when maintenance is performed or when the electrical system is serviced. Disconnect the battery ground leads. Tape the leads in order to help prevent sparks.
Disconnect the connector for the unit injector that is located on the valve cover base. This procedure will help prevent personal injury from the high voltage to the unit injectors. Do not come in contact with the unit injector terminals while the engine is operating.
Do not attempt any repairs or any adjustments to the engine while the engine is operating.
Do not attempt any repairs that are not understood. Use the proper tools. Replace any equipment that is damaged or repair the equipment.
When starting a new engine or an engine which has not been started since service has been performed, make provisions to stop the engine if an overspeed occurs. Shutting down the engine may be accomplished by shutting off the fuel supply and/or the air supply to the engine.
Start the engine from the operator station (cab). Never short across the starting motor terminals or the batteries which could bypass the engine neutral start system and/or the electrical system could be damaged.Cautiously remove the following parts:Note: To help prevent spraying or splashing of pressurized fluids, hold a rag over the part that is being removed.
Filler caps
Grease fittings
Pressure taps
Breathers
Drain plugsUse caution when cover plates are removed. Gradually loosen but do not remove the last two bolts or nuts that are located at opposite
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
2285617
BUSHING
320C, 324D, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330D, 330D FM, 330D L, 330D L...
320C, 324D, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330D, 330D FM, 330D L, 330D L...
7Y3553
BUSHING
1190T, 1290T, 2391, 2491, 320 L, 320B, 320C, 320N, 322, 322 L, 322 LN, 322B, 322B L, 322C, 322C FM, 325, 325 L, 325 LN, 325B L, 325C, 325C L, 330, 330 FM L, 330 L, 330B, 522, 522B, 532, 552, 552 2, TK...
1190T, 1290T, 2391, 2491, 320 L, 320B, 320C, 320N, 322, 322 L, 322 LN, 322B, 322B L, 322C, 322C FM, 325, 325 L, 325 LN, 325B L, 325C, 325C L, 330, 330 FM L, 330 L, 330B, 522, 522B, 532, 552, 552 2, TK...
2402916
BUSHING
321C, 321D LCR, 322B LN, 322C, 325C, 325C FM, 325D L, 328D LCR, 330C, 330C L, 330D L, 345B II, 345C L, 365B II, 365C, 365C L, 385B, 385C L
321C, 321D LCR, 322B LN, 322C, 325C, 325C FM, 325D L, 328D LCR, 330C, 330C L, 330D L, 345B II, 345C L, 365B II, 365C, 365C L, 385B, 385C L
1297770
BUSHING
320B, 328D LCR
320B, 328D LCR
1052575
BUSHING
320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322B, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B, 325C, 325C L, 326D L, 328D LCR, 330C L, 375
320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322, 322B, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B, 325C, 325C L, 326D L, 328D LCR, 330C L, 375
1195325
BUSHING
320B, 320D, 322B, 325B, 375
320B, 320D, 322B, 325B, 375
1195324
BUSHING
320B, 320B FM LL, 320C FM, 320D, 322B, 325B, 375
320B, 320B FM LL, 320C FM, 320D, 322B, 325B, 375
5I8634
BUSHING
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
1633753
BUSHING
320B, 320C, 320C FM, 320C L, 321B, 321C
320B, 320C, 320C FM, 320C L, 321B, 321C
2366273
BUSHING
320C, 322C, 325C, 325C FM, 330C, 330C L, 385B, 385C L
320C, 322C, 325C, 325C FM, 330C, 330C L, 385B, 385C L
2081959
BUSHING
321C, 322C, 325C, 330C, 330C FM, 330C L, 385B
321C, 322C, 325C, 330C, 330C FM, 330C L, 385B
2276908
BUSHING
320C, 325C, 325C FM, 325D
320C, 325C, 325C FM, 325D
1785488
BUSHING
307C, 311C, 320C
307C, 311C, 320C
2185196
BUSHING
307C, 308C
307C, 308C
2423740
BUSHING
307C, 308C
307C, 308C
2185429
BUSHING
307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
2969438
BUSHING
307C, 307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307C, 307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
2185197
BUSHING
307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR
4442033
BUSHING
311D LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
311D LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
1252932
BUSHING
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1905895
BUSHING
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1905893
BUSHING
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
5I7631
BUSHING
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
5I7539
BUSHING
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN