9V3852 BUSHING Caterpillar parts
814F, 814F II, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F
Rating:
Alternative (cross code) number:
CA9V3852
9V-3852
9V3852
CA9V3852
9V-3852
9V3852
Weight: 3 pounds 1 kg.
Information:
ID
70.112
mm
OD
120.772
mm
WIDTH
30
mm
LANDFILL COMPACTOR, WHEEL LOADER,
Related part:
9V3852
BEARING-SLV-YM
4509166
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$86.53
12 Nov 2023
CN: RELIABLE SPARE
YNRSP 9V3852 Spacer Sleeve Bearing for Heavy Equipment (2Pcs)
YNRSP Brand: YNRSP || Part Number: 9V3852 || Part Type: Spacer || Weight: 3.96 lbs (1.8 kg) || Easy in-and-out fit
YNRSP Brand: YNRSP || Part Number: 9V3852 || Part Type: Spacer || Weight: 3.96 lbs (1.8 kg) || Easy in-and-out fit
$44.16
06 Nov 2023
CN: RELIABLE SPARE
YNRSP 9V3852 Spacer Sleeve Bearing for Heavy Equipment (1Pcs)
YNRSP Brand: YNRSP || Part Number: 9V3852 || Part Type: Spacer || Weight: 3.96 lbs (1.8 kg) || Easy in-and-out fit
YNRSP Brand: YNRSP || Part Number: 9V3852 || Part Type: Spacer || Weight: 3.96 lbs (1.8 kg) || Easy in-and-out fit
$27.36
07 Oct 2023
Amazon.com
CTP 9V3852 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
32
For full view, you need register
Compatible equipment models: 9V3852:
Information:
Assembly Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the components of the fuel transfer pump for damage. Replace the components, if necessary.
Clean all of the components before assembly.
Illustration 1 g00544796
Install seat washers (3) .
Push valves (4) into position.Note: It is possible for the valves to be installed incorrectly. Refer to Illustration 1 for the correct installation.
When valves (4) are installed, peen the edge of the valve housing evenly in six places. This will keep valves (4) in position.
Install rocker lever (11), pin (9), and link arm (8) into the bottom half of the fuel transfer pump.
Install the return spring and ensure that the ends of the spring are installed correctly.
Using a soft hammer and a suitable adapter install two retainers (10) into the grooves. Ensure that retainers (10) fasten the pin. Peen the open ends of the grooves in order to fasten the retainers in position.
Install the diaphragm spring (12) under diaphragm assembly (5). Place spring seat washer (7) and stem seal (6) on the pull rod.
Ensure that the small diameter at the top of the seal is on the round section of the pull rod.
Place diaphragm assembly (5) over the lower half of the body of the fuel transfer pump. Ensure that the blade of the pull rod is aligned with the slot of link arm (8) .
Press lightly on diaphragm assembly (5) until the notch in the pull rod is in the slot of link arm (8). Rotate diaphragm assembly (5) at 90 degrees in either direction. This will engage the pull rod in the slot of link arm (8) .
Push rocker lever (11) toward the body of the fuel transfer pump. Push rocker lever (11) until diaphragm assembly (5) is level with the flange on the body of the fuel transfer pump.
Install the top half of the body of the fuel transfer pump and align the marks on the flanges. Keep pressure on rocker lever (11). Install spring washers and the screws. Tighten the screws evenly.
Install gauze (2) .
Install the gasket and cover (1) .Note: Refer to the Testing and Adjusting, "Fuel Transfer Pump Pressure Test" for the correct procedure.End By: Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the components of the fuel transfer pump for damage. Replace the components, if necessary.
Clean all of the components before assembly.
Illustration 1 g00544796
Install seat washers (3) .
Push valves (4) into position.Note: It is possible for the valves to be installed incorrectly. Refer to Illustration 1 for the correct installation.
When valves (4) are installed, peen the edge of the valve housing evenly in six places. This will keep valves (4) in position.
Install rocker lever (11), pin (9), and link arm (8) into the bottom half of the fuel transfer pump.
Install the return spring and ensure that the ends of the spring are installed correctly.
Using a soft hammer and a suitable adapter install two retainers (10) into the grooves. Ensure that retainers (10) fasten the pin. Peen the open ends of the grooves in order to fasten the retainers in position.
Install the diaphragm spring (12) under diaphragm assembly (5). Place spring seat washer (7) and stem seal (6) on the pull rod.
Ensure that the small diameter at the top of the seal is on the round section of the pull rod.
Place diaphragm assembly (5) over the lower half of the body of the fuel transfer pump. Ensure that the blade of the pull rod is aligned with the slot of link arm (8) .
Press lightly on diaphragm assembly (5) until the notch in the pull rod is in the slot of link arm (8). Rotate diaphragm assembly (5) at 90 degrees in either direction. This will engage the pull rod in the slot of link arm (8) .
Push rocker lever (11) toward the body of the fuel transfer pump. Push rocker lever (11) until diaphragm assembly (5) is level with the flange on the body of the fuel transfer pump.
Install the top half of the body of the fuel transfer pump and align the marks on the flanges. Keep pressure on rocker lever (11). Install spring washers and the screws. Tighten the screws evenly.
Install gauze (2) .
Install the gasket and cover (1) .Note: Refer to the Testing and Adjusting, "Fuel Transfer Pump Pressure Test" for the correct procedure.End By: Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Install".
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
533, 543, 545, 910K, 914K, 930K, 936, 936F, 938F, 938G, 938G II, 938H, 950B, 950F, 950F II, 960F, G936, HA770, HA771, HA870, HA871, HYDRAULIC, IT38F, IT38G, IT38G II, IT38H, TK370, TK371, TK380, TK381
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
814, 815, 815B, 816, 816B, 950, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966C, 966D, 966F, 966G, 966R, IT62G
936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, 966R, G936, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
227, 950F II, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966C, 966G, 966G II, 966H, 966K, 966R, 972G, 972G II, 972H, 972K, 980G, 980G II, 980H, 980K, 990H, IT62G
928HZ, 930G, 950G II, 950H, 962G II, 962H, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972K, 972M, 972M XE, 986H
924K, 930K, 950 GC, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, HYDRAULIC
528, 528B, 530B, 920, 930, 930R, 950, 950B, 966D
966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972K, 972M, 972M XE
966F, 966F II, 970F
950K, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972M, 972M XE, R1300, R1300G, R1300G II
814F, 814F II, 815F, 815F II, 816F, 816F II, R1600, R1600G, R1600H
966F, 966F II, 970F
994, 994D
2783282
BUSHING
994, 994D
994, 994D
988K, 994, 994D, 994F, 994H
8X0146
BUSHING-TERMINAL
994, 994D, 994F, 994H
994, 994D, 994F, 994H
8X0758
BUSHING
994, 994D, 994F, 994H
994, 994D, 994F, 994H
0546734
BUSHING-TERMINAL
980F, CB-334D, CB-334E, CB-335D, CB-34, CB-434, D350E, D400E
980F, CB-334D, CB-334E, CB-335D, CB-34, CB-434, D350E, D400E
824C, 980F, 980F II, AD40, AE40, R1700 II
6C4175
BUSHING-TERMINAL
950F, 966F, 980F
950F, 966F, 980F
6C4177
BUSHING-TERMINAL
950F, 966F, 980F
950F, 966F, 980F
6C4176
BUSHING-TERMINAL
950F, 966F, 980F
950F, 966F, 980F
950K, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972M, 972M XE, R1300, R1300G, R1300G II