3063351 C-FRAME AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA3063351
306-3351
3063351
CA3063351
306-3351
3063351
Weight: 229 pounds 103 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$139.23
19 Oct 2020
-: -
DIE - SYNFLEX FOR HYSTER: 3063351
HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || DIE - SYNFLEX. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY3063351 3063351 Â HYSTER 3063351 Â HYSTER3063351 3063351 Â Â . All Brand new & rebuilt items comes with 1 year warranty.
HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || DIE - SYNFLEX. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY3063351 3063351 Â HYSTER 3063351 Â HYSTER3063351 3063351 Â Â . All Brand new & rebuilt items comes with 1 year warranty.
Information:
Illustration 1 g01271498
Schematic for the "Cat Data Link"Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01167488
Engine view (typical example) (1) J1/P1 connectors
Thoroughly inspect connector (1). Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01104274
P1 terminals that are associated with the "Cat Data Link" (P1-8) Cat Data Link + (P1-9) Cat Data Link −
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the "Cat Data Link".
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.STOPTest Step 2. Check for a Short Circuit
Disconnect the P1 ECM connector.
Disconnect Cat ET from the service tool connector.
Disconnect any other control modules from the "Cat Data Link". Refer to Illustration 1.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the Cat Data Link    
Connector and Terminal    Terminal    
P1-8 (Cat Data Link +)     All of the other terminals on the P1 connector    
Ground stud
P1-9 (Cat Data Link -)     All of the other terminals on the P1 connector    
Ground stud Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. Proceed to Test Step 3.
Not OK - At least one check of the resistance does not indicate an open circuit. There is a short circuit in the harness or in a connector.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved.STOPTest Step 3. Check for an Open Circuit
Fabricate a jumper wire. Use the jumper wire in order to create a short circuit between terminals D (Cat Data Link +) and terminal E (Cat Data Link −) on the service tool connector.
Measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −).
Measure the resistance between the terminals at the connector for each control module that was connected to the "Cat Data Link". Refer to Illustration 1.Expected Result:Each check of the resistance indicates a short circuit.Results:
OK - Each check of the resistance indicates a short circuit.Repair: Perform the following procedure:
Connect the J1/P1 connectors. Connect Cat ET to the service tool connector.
Check the "Cat Data Link" for proper operation.
Parts c Caterpillar catalog:
2Y7875
C-FRAME REINF-
Caterpillar
Caterpillar
2Y7854
C-FRAME REINF-
Caterpillar
Caterpillar
2K4996
C-FRAME A.
Caterpillar
Caterpillar
2J6656
C-FRAME A.
Caterpillar
Caterpillar
2J3651
C-FRAME A.
Caterpillar
Caterpillar
2J1138
C-FRAME G.
Caterpillar
Caterpillar
3J4614
C-FRAME A.
Caterpillar
Caterpillar
3J3488
C-FRAME A.-LH
Caterpillar
Caterpillar
3J3487
C-FRAME A.-RH
Caterpillar
Caterpillar
3H4409
C-FRAME A.
Caterpillar
Caterpillar
3F6298
C-FRAME
Caterpillar
Caterpillar
3F5398
C-FRAME A.
Caterpillar
Caterpillar