1586657 CAB AR Caterpillar parts
D6R
Rating:
Alternative (cross code) number:
CA1586657
158-6657
1586657
CA1586657
158-6657
1586657
TRACK-TYPE TRACTOR,
Compatible equipment models: 1586657:
Information:
34. Remove plug (53) and fill steering clutch compartment until it is even with the bottom of oil level plug hole (54). See the Maintenance Guide.Disassemble Steering Clutches
Start By:a. remove steering clutches 1. Remove brake band (2) and outer drum (1) from the steering clutch. 2. Install tooling (B) to the end of the clutch shaft and install it in a vise.3. Remove lock (3). Use tooling (A) and loosen nut (4) until it is even with the top of the shaft.
Do not remove nut (4). This will keep the drum on the shaft when it is loosened from the taper on the shaft.
4. Remove the steering clutch from the vise. The weight is approximately 45 kg (100 lb.).5. Use tooling (D) as shown to push the shaft from the inner drum. Remove tooling (D) and nut (4). Remove the shaft from the steering clutch. 6. Install tooling (H) on the other side of the steering clutch and install it in a vise.7. Remove two setscrews (5). Use tool (E) and remove spanner nut (6) from the plate assembly. 8. Bend locks (7) down and remove bolts (8) that hold the yoke in place.9. Remove yoke (9) from the plate assembly. 10. Use a pry bar on each side of the bearing cage and remove bearing cage (10) from the plate assembly. 11. Remove retaining ring (11) from bearing cage (10). 12. Remove bearing (12) from bearing cage (10). 13. Put two pieces of wood (13) on tool (F), as shown, as a support for the steering clutches. Install drum (1). Make an alignment of the centers of the clutches and drum (1).
Use only enough force to put the steering clutch springs under compression to remove the locks from the studs. Be extra careful that 5P3036
Start By:a. remove steering clutches 1. Remove brake band (2) and outer drum (1) from the steering clutch. 2. Install tooling (B) to the end of the clutch shaft and install it in a vise.3. Remove lock (3). Use tooling (A) and loosen nut (4) until it is even with the top of the shaft.
Do not remove nut (4). This will keep the drum on the shaft when it is loosened from the taper on the shaft.
4. Remove the steering clutch from the vise. The weight is approximately 45 kg (100 lb.).5. Use tooling (D) as shown to push the shaft from the inner drum. Remove tooling (D) and nut (4). Remove the shaft from the steering clutch. 6. Install tooling (H) on the other side of the steering clutch and install it in a vise.7. Remove two setscrews (5). Use tool (E) and remove spanner nut (6) from the plate assembly. 8. Bend locks (7) down and remove bolts (8) that hold the yoke in place.9. Remove yoke (9) from the plate assembly. 10. Use a pry bar on each side of the bearing cage and remove bearing cage (10) from the plate assembly. 11. Remove retaining ring (11) from bearing cage (10). 12. Remove bearing (12) from bearing cage (10). 13. Put two pieces of wood (13) on tool (F), as shown, as a support for the steering clutches. Install drum (1). Make an alignment of the centers of the clutches and drum (1).
Use only enough force to put the steering clutch springs under compression to remove the locks from the studs. Be extra careful that 5P3036
Caterpillar SIS machinery equipment:
Parts cab Caterpillar catalog:
4Y9483
CAB GROUP
D6R, D7R
D6R, D7R
1065637
CAB AS
D6R, D7R
D6R, D7R
3T0639
CAB AR
D8L
D8L
2070135
CAB GP
385B
385B
3859553
CAB AR
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
1125094
CAB GP
322 FM L, 325, 330
322 FM L, 325, 330
3320672
CAB GP-ENCLOSED ROPS
AD55B, AD60
AD55B, AD60
3290391
CAB AR
980K
980K
8V1055
CAB GP
834B, 836, 988B, 992C
834B, 836, 988B, 992C
3514679
CAB GP
776D, 777D
776D, 777D
2253174
CAB AR
140H, 160H
140H, 160H
3859554
CAB AR
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
1871884
CAB AR-ENCLOSED ROPS
824G II, 826G II
824G II, 826G II