AVSPARE.COM
parts catalog

CAB GP 3236949 - Caterpillar



3236949 CAB GP Caterpillar parts CAB
Rating:
86
Alternative (cross code) number:
CA3236949
323-6949
3236949
Caterpillar 3236949 CAB GP

Buy CAB GP 3236949 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 12 g06091258
Press rpm increase switch (16) on the throttle control to place the engine in high idle. The engine speed should increase to 2200 rpm.
Monitor the hydraulic oil temperature on operator display (15). Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Record the pressure at charge pressure tap (13). The charge pressure should be 2425 175 kPa (352 25 psi).
Record the pressure at case drain tap (14). The case drain pressure should be 175 kPa (25 psi) to 410 kPa (59 psi).
Subtract the pressure that was recorded in Step 7 from the pressure that was recorded in Step 6. The differential pressure should be 1950 kPa (283 psi) to 2500 kPa (363 psi).
Press rpm decrease switch (9) for the throttle control once to operate the engine in low idle.
Shut off the engine. Either place machine power switch (10) in the OFF position or press and hold push to start switch (7) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode.
If the push to start switch (7) was used to shut off the engine, move machine power switch (10) to the OFF position.
If the pressure is within the specified range, go to "Flushing Valve Test Procedure". If the pressure is not within the specified range, go to "Charge Relief Adjustment Procedure", Step 1.Flushing Valve Test Procedure
Move machine power switch (10) to the ON position.
Press push to start switch (7) for 2 seconds to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated.Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle is necessary to restart the process.
Illustration 13 g06091258
Press rpm increase switch (16) on the throttle control to place the engine in high idle. The engine speed should increase to 2200 rpm.
Monitor the hydraulic oil temperature on operator display (15). Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Operate the engine at low idle for a few minutes.
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Illustration 14 g06091261
Rotate speed dial (17) to one quarter of maximum.
Press parking brake switch (3) to change the status of the parking brake to "disengaged".
Illustration 15 g06091265
Squeeze trigger (18), and move propel lever (4) slowly to the FULL FORWARD position. Observe the pressure at charge pressure tap (13). The pressure should momentarily decrease.
Move propel lever (4) to the NEUTRAL position. Then, squeeze trigger (18), and move propel lever to the FULL REVERSE position. Observe the pressure at charge pressure tap (13). The pressure should momentarily decrease.
Move propel lever (4) to the NEUTRAL position.


Parts cab Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.