1355049 CABLE AS Caterpillar parts
30/30, AP-1000B, AP-1055B, AP-600D, AP-650B, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, AS2251, AS2301, BG-225B, BG-225C, BG-2455C, BG-245C, BG1000E, BG1055E, BG655D, CB22B, CB24B, ...
Rating:
Alternative (cross code) number:
CA1355049
135-5049
1355049
CA1355049
135-5049
1355049
Weight: 0.04 pounds 0 kg.
Information:
CABLE DIAMETER
2.36
mm
LARGE EYE DIAMETER
20
mm
LENGTH
152
mm
LOAD
500N
kg
SMALL EYE DIAMETER
13
mm
ASPHALT PAVER, VIBRATORY COMPACTOR,
Compatible equipment models: 1355049:
Number on catalog scheme:
1
For full view, you need register
Information:
Probable Causes
Batteries
Switches
Starting Circuit
Starting Motor or Flywheel Ring Gear
Engine Accessories
Internal Engine ProblemRecommended Actions
Note: The procedures have been listed in order of probability. Complete the following procedures in the order that is provided.
Table 1
Troubleshooting Test Steps Values Results
1. Inspection of the Batteries and Battery Cables
A. Inspect the main power switch, battery posts, and battery cables for loose connections and for corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Tighten any loose connections.
B. Inspect the batteries.
C. Charge the batteries. Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
Test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6 v, 8 v, and 12 v Lead Acid Batteries".
Batteries
Result The batteries and cables are OK.
Proceed to Test Step 2.
Result The batteries and cables are not OK.
Repair: Make the necessary repairs.
2. Switches and/or Circuit Breakers (if applicable)
A. If equipped, check any switches and/or circuit breakers that may interfere with the engine cranking. Refer to the applications electrical schematic for additional information.
Switches and/or Circuit Breakers
Result The switches and/or circuit breakers are OK.
Proceed to Test Step 3.
Result The switches and/or circuit breakers are not OK.
Repair: Make the necessary repairs.
3. Starting Motor Solenoid and Starting Circuit
Test the operation of the starting motor circuit. Refer to Systems Operation/Testing and Adjusting, "Electrical System" for additional information.
Starting Motor Solenoid and Circuit
Result The starting motor solenoid and circuit are OK.
Proceed to Test Step 4.
Result The starting motor solenoid and circuit are not OK.
Repair: Make the necessary repairs.
4. Inspect the Starter Pinion and Flywheel Ring Gear
A. Test the operation of the starting motor.
B. Check the pinion clearance. Inspect the pinion and the flywheel ring gear for damage. Refer to Systems Operation/Testing and Adjusting, "Electrical System" for additional information.
Starter Pinion and Flywheel Ring Gear
Result The starter pinion and flywheel ring gear are OK.
Proceed to Test Step 5.
Result The starter pinion and flywheel ring gear are not OK.
Repair: Make the necessary repairs.
5. Inspect Engine Accessories and the Transmission (if applicable)
A. Ensure free movement of the driveline.
B. Remove any engine accessories that may lock up the engine and inspect any engine accessories that may lock up the engine.
The following list illustrates examples of engine accessories that may lock up the engine:
1. Hydraulic pump that is driven from the rear gear group
2. Air compressor
3. Engine oil pump
4. Other components that are driven by the engine
Engine Accessories and Transmission
Result The engine accessories and transmission are OK.
Proceed to Test Step 6.
Result The engine accessories and transmission are not OK.
Repair: Make the necessary repairs.
6. Hydraulic Cylinder Lock
A. If an injector has been replaced, evacuate any fluids from the cylinder and attempt to start the engine. Fuel will flow from the cylinder head into the cylinders when a unit injector is removed.
B. If the engine will not start, check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors. Check for damaged seals. Determine the type of fluid that locked up the cylinder.
C. If there was a coolant leak, determine the cause of
Batteries
Switches
Starting Circuit
Starting Motor or Flywheel Ring Gear
Engine Accessories
Internal Engine ProblemRecommended Actions
Note: The procedures have been listed in order of probability. Complete the following procedures in the order that is provided.
Table 1
Troubleshooting Test Steps Values Results
1. Inspection of the Batteries and Battery Cables
A. Inspect the main power switch, battery posts, and battery cables for loose connections and for corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Tighten any loose connections.
B. Inspect the batteries.
C. Charge the batteries. Refer to Special Instruction, SEHS7633, "Battery Test Procedure".
Test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6 v, 8 v, and 12 v Lead Acid Batteries".
Batteries
Result The batteries and cables are OK.
Proceed to Test Step 2.
Result The batteries and cables are not OK.
Repair: Make the necessary repairs.
2. Switches and/or Circuit Breakers (if applicable)
A. If equipped, check any switches and/or circuit breakers that may interfere with the engine cranking. Refer to the applications electrical schematic for additional information.
Switches and/or Circuit Breakers
Result The switches and/or circuit breakers are OK.
Proceed to Test Step 3.
Result The switches and/or circuit breakers are not OK.
Repair: Make the necessary repairs.
3. Starting Motor Solenoid and Starting Circuit
Test the operation of the starting motor circuit. Refer to Systems Operation/Testing and Adjusting, "Electrical System" for additional information.
Starting Motor Solenoid and Circuit
Result The starting motor solenoid and circuit are OK.
Proceed to Test Step 4.
Result The starting motor solenoid and circuit are not OK.
Repair: Make the necessary repairs.
4. Inspect the Starter Pinion and Flywheel Ring Gear
A. Test the operation of the starting motor.
B. Check the pinion clearance. Inspect the pinion and the flywheel ring gear for damage. Refer to Systems Operation/Testing and Adjusting, "Electrical System" for additional information.
Starter Pinion and Flywheel Ring Gear
Result The starter pinion and flywheel ring gear are OK.
Proceed to Test Step 5.
Result The starter pinion and flywheel ring gear are not OK.
Repair: Make the necessary repairs.
5. Inspect Engine Accessories and the Transmission (if applicable)
A. Ensure free movement of the driveline.
B. Remove any engine accessories that may lock up the engine and inspect any engine accessories that may lock up the engine.
The following list illustrates examples of engine accessories that may lock up the engine:
1. Hydraulic pump that is driven from the rear gear group
2. Air compressor
3. Engine oil pump
4. Other components that are driven by the engine
Engine Accessories and Transmission
Result The engine accessories and transmission are OK.
Proceed to Test Step 6.
Result The engine accessories and transmission are not OK.
Repair: Make the necessary repairs.
6. Hydraulic Cylinder Lock
A. If an injector has been replaced, evacuate any fluids from the cylinder and attempt to start the engine. Fuel will flow from the cylinder head into the cylinders when a unit injector is removed.
B. If the engine will not start, check for fluid in the cylinders (hydraulic cylinder lock) by removing the individual unit injectors. Check for damaged seals. Determine the type of fluid that locked up the cylinder.
C. If there was a coolant leak, determine the cause of
Cat SIS web machinery list:
Parts cable Caterpillar catalog:
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16M, 21...
3798315
CABLE AS
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
3798316
CABLE AS
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
3798318
CABLE AS
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
CS-54B, CS-56B, CS-68B, CS-74B, CS-78B
3798282
CABLE AS
CS-54B
CS-54B
3798283
CABLE AS-GROUND
CS-54B
CS-54B
4315575
CABLE AS
CS-54B
CS-54B
3927795
CABLE AS
CS-54B
CS-54B
3798285
CABLE AS
CS-54B
CS-54B
3453342
CABLE AS
CS-56
CS-56
3540085
CABLE AS
AP-655D
AP-655D
3540087
CABLE AS
AP-655D
AP-655D
1439954
CABLE AS
30/30, DEUCE
30/30, DEUCE
1395517
CABLE AS
30/30, DEUCE
30/30, DEUCE
1395516
CABLE AS
30/30, DEUCE
30/30, DEUCE
1439953
CABLE AS
30/30, DEUCE
30/30, DEUCE
9W2489
CABLE AS
30/30, 578, 583R, 824C, 826C, 980C, 980F, 980F II, DEUCE, R1600, R1600G, R1700 II, R1700G, RM-350B, SM-350
30/30, 578, 583R, 824C, 826C, 980C, 980F, 980F II, DEUCE, R1600, R1600G, R1700 II, R1700G, RM-350B, SM-350
5Y1423
CABLE AS
30/30, AP-1055D, BG-2455D, BG-260D, CB-14, CB-22, CB-334E, CB-34, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CB-634D, CP-433B, CP-433C, CS-431C, CS-433C, D5B, D5E, D6D, DEUCE, PF-29...
30/30, AP-1055D, BG-2455D, BG-260D, CB-14, CB-22, CB-334E, CB-34, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-634, CB-634C, CB-634D, CP-433B, CP-433C, CS-431C, CS-433C, D5B, D5E, D6D, DEUCE, PF-29...
3K1705
CABLE AS
3208, D7F
3208, D7F
16, 1673C, 245, 245B, 245D, 3306, 3306C, 561C, 561D, 571G, 572G, 583K, 594, 594H, 627, 627B, 627E, 627F, 627G, 637, 637D, 637E, 637G, 657B, 777, 777B, 824C, 825C, 826C, 980C, 994, AP-1055B, AP-200B, C...
7J6590
CABLE AS
1673C, 3306, 3306C, 613, D7F
1673C, 3306, 3306C, 613, D7F
1610843
CABLE
30/30
30/30
6W1886
CABLE
30/30, 768C, 826G II, 826H, 836H, 916, 918F, 936, 950F II, 963, CB-434B, CB-434C, CB-534B, CB-534C, CB-634, CB-634C, CP-433C, CP-563, CS-323C, CS-431C, CS-433C, CS-531C, CS-533C, CS-563C, CS-573C, CS-...
30/30, 768C, 826G II, 826H, 836H, 916, 918F, 936, 950F II, 963, CB-434B, CB-434C, CB-534B, CB-534C, CB-634, CB-634C, CP-433C, CP-563, CS-323C, CS-431C, CS-433C, CS-531C, CS-533C, CS-563C, CS-573C, CS-...
1448530
CABLE
DEUCE
DEUCE