CABLE GP-CONTROL 1686500 - Caterpillar

Figure 4. Partial View Of Hose Layout For Stick Circuit (3) 951417 Connector. (4) 951424 Elbow 90°. (5) 5I5902 Hose. (6) 7X0623 Washer (Plain). (7) 8T4198 Bolt. (8) 3D2824 Seal, O-ring. (9) 5I5889 Elbow 90°. (10) 5I6146 Valve (Drift Reduction). (11) 931293 Clamp. (12) 7X0622 Washer (Plain). (13) 8T4910 Bolt. (14) 8T4183 Bolt. (15) 930352 Washer. (16) 5I5911 Hose. (17) 5I5858 Joint. (19) 951596 Seal, O-ring. (20) 951595 Seal, O-ring. (21) 950657 Bolt (Hexagon Socket). (22) 951599 Seal, O-ring. (23) 5I6872 Support. (24) 5I5855 Pipe. (25) 5K9090 Seal, O-ring. (26) 5I5854 Pipe. (A) Hose. (D) Hose.6. Install 5I6146 Drift Reduction Valve (10) to 5I6872 Support (23) with two 8T4198 Bolts (7) and 7X0623 Washers (Plain) (6). Tighten connection to 40 3 N m (30 3 lb ft). Refer to Figure 4.7. Install support (23) to support (1) located on the left side plate of the swing frame. Use two 8T4183 Bolts (14) and 930352 Washers (15) to fasten the plates. Tighten connection to 71 7 N m (52 5 lb ft). Refer to Figure 4.
Figure 5. View Of Joint On Top Of Swing Motor (19) 951596 Seal, O-ring. (A) Hose. (B) Joint. (C) Joint. (D) Hose. (E) Elbow. Hose (D) is from boom drift reduction valve.8. Disconnect two hoses (A) and (D) from the top of the swing motor. Refer to Figure 5.9. Remove joint (C), joint (B), and elbow (E) as a unit. Refer to Figure 5.
Figure 6. View Of Joint On Top Of Swing Motor (3) 951417 Connectors. (4) 951424 Elbow. (17) 5I5858 Joint. (19) 951596 Seal, O-ring. (A) Hose. (D) Hose. Hose (D) is from boom drift reduction valve.10. Install 5I5858 Joint (17) and 951596 Seal, O-ring (19) in its place. Tighten joint (17) to 162 20 N m (120 15 lb ft). Refer to Figure 6.11. Install 951424 Elbow 90° (4) to joint (17). Tighten elbow (4) to 118 14 N m (87 10 lb ft). Refer to Figure 6.12. Install two 951417 Connectors (3) to joint (17). Tighten connector (3) to 118 14 N m (87 10 lb ft). Refer to Figure 4.13. Connect hose (A) to connector (3) and hose (D) to elbow (4). Refer to Figure 4 and Figure 6. Hose (D) connects to the Boom Drift Reduction Valve. If this modification has not been added, install 950969 Plug (18) in place of hose (D).14. Connect one end of 5I5854 Pipe (26) with 951595 Seal, O-ring (20) to the retract port of the stick control valve with the four socket bolts removed in Step 1. Install 951599 Seal, O-ring (22) to the other end of pipe (26). Connect pipe (26) and seal, O-ring (22) to the Pi port of valve (10) using four 950657 Bolts (21). Tighten the bolt to 33 4 N m (25 3 lb ft). Refer to Figure 4.15. Install 5I5855 Pipe (24) with 951599 Seal, O-ring (22) and four 950657 Bolts (21) to P2 port