3423114 CABLE AS Caterpillar parts
320E L
Rating:
Alternative (cross code) number:
CA3423114
342-3114
3423114
CA3423114
342-3114
3423114
Weight: 1 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 3423114:
Number on catalog scheme:
14
For full view, you need register
Information:
Start By: a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) to show the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 4 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 3 upper main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Install the main bearings dry when clearance checks are made. Put clean engine oil on the main bearings for final assembly.5. Install the lower bearings in the bearing caps.6. Install the upper bearing in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block.The serviceman must be very careful to use Plastigage correctly. The following points must be remembered: ... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.7. Check the bearing clearance with tool (B) as follows:
When Plastigage is used to check bearing clearance, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Install the main bearings dry when clearance checks are made. Put clean engine oil on the main bearings for final assembly.5. Install the lower bearings in the bearing caps.6. Install the upper bearing in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block.The serviceman must be very careful to use Plastigage correctly. The following points must be remembered: ... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.7. Check the bearing clearance with tool (B) as follows:
When Plastigage is used to check bearing clearance, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be
Caterpillar parts catalog:
Parts cable Caterpillar catalog:
120H, 120K, 120K 2, 120M, 12H, 12K, 12M, 12M 2, 135H, 140H, 140K, 140K 2, 140M 2, 143H, 14H, 160H, 160K, 160M 2, 163H, 16H, 2290, 236D, 2390, 2391, 242D, 246D, 2470C, 2491, 24M, 2570C, 257D, 259D, 262...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16M, 21...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H, 16M, 21...
3484939
CABLE
2384C, 2484C, 2570C, 2670C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 559C, 563C, 573C, 579C, BG1000E, BG1055E, C6.6, C7....
2384C, 2484C, 2570C, 2670C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 559C, 563C, 573C, 579C, BG1000E, BG1055E, C6.6, C7....
0993645
CABLE-LANYARD
303.5C, 303.5D, 303.5E, 303E CR, 304, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LR...
303.5C, 303.5D, 303.5E, 303E CR, 304, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LR...
3346550
CABLE AS
312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 32...
312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 32...
3068689
CABLE AS
312E, 312E L, 316E L, 318E L, 320D FM, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 3...
312E, 312E L, 316E L, 318E L, 320D FM, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 3...
3508462
CABLE AS
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 34...
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 349E, 349E L, 34...
3470115
CABLE
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D2 L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E ...
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D2 L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E ...
3423113
CABLE AS
320E L
320E L
3508372
CABLE AS-COMMUNICATION
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3640360
CABLE AS
324E L, 324E LN, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
324E L, 324E LN, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
3422894
CABLE AS
324E L, 324E LN, 329E L
324E L, 324E LN, 329E L
3886784
CABLE AS
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3690094
CABLE AS
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3886778
CABLE AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3423221
CABLE AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3423220
CABLE AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3423219
CABLE AS
320E, 320E L, 320E LN, 323E L
320E, 320E L, 320E LN, 323E L
3423118
CABLE AS
320E L
320E L
3423117
CABLE AS
320E L
320E L