3423125 CABLE AS Caterpillar parts
324D L, 329D, 329D L, 329D LN
Rating:
Alternative (cross code) number:
CA3423125
342-3125
3423125
CA3423125
342-3125
3423125
Weight: 1 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 3423125:
Number on catalog scheme:
7
For full view, you need register
Information:
You must read and understand the warnings and instructions contained in the Safety section of this manual before performing any operation or maintenance procedures.Transmission Oil Filter
Change Filter
The transmission filter is located on the left side of the machine under the steps. 1. Remove the filter element with a strap-type wrench.2. Clean the filter housing base. Make sure all of the old filter gasket is removed.3. Apply a light coat of oil to the gasket of the new filter.4. Install the new filter by hand. When the gasket contacts the filter base, tighten the filter three-quarter of a turn more.5. Start the engine. Apply the service brake.6. Slowly operate the transmission controls to circulate the transmission oil.7. Move the transmission control lever into NEUTRAL. Engage the parking brake. Inspect for leaks. 8. Maintain the oil level between the marks on the low idle side of the dipstick with the transmission in neutral. Add oil if necessary.9. Stop the engine.Hydraulic Oil System
Change Filter
1. Remove the oil fill cap slowly to relieve the tank pressure before changing the filters.Hydraulic Oil Tank Filter
2. Loosen the filter housing cover retaining bolt. Remove the filter cover.3. Inspect the cover seal. Replace if necessary.4. Remove and discard the two filter elements.5. Remove the screen. Wash screen in clean, nonflammable solvent. Dry the screen.6. Install the screen and two new filter elements.7. Install the cover. 8. Maintain the hydraulic oil level above the ADD COLD mark in the sight gauge.9. Inspect the fill cap gasket. Replace the gasket, if damaged. Install the oil fill cap.Fuel System
Clean and Change Filters
Do not fill fuel filters with fuel before installing them. Contaminated fuel will cause accelerated wear to fuel system parts.
Wash the Primary Filter Element
1. Open the access cover of the machine. 2. Loosen the filter housing retaining bolt (1).3. Remove the housing (2) and element.4. Remove the element from the case.5. Wash the element and housing in clean, nonflammable solvent.6. Dry the element using pressure air.7. Clean the filter case base.8. Inspect the seal. Replace if damaged.9. Insert the clean element.10. Install the element and case into housing.11. Retighten the retaining bolt to a torque of 24 4 N m (18 3 lb ft).12. Close the access cover.Change Secondary Fuel Filter
1. Open the access cover. 2. Remove and discard the filter.3. Clean the filter mounting base. Be sure all of the old seal is removed.4. Coat the seal of a new filter with clean diesel fuel.5. Install the new filter by hand. When the seal contacts the base, tighten three-quarter of a turn more.There are rotation-index marks 90° apart on the filter. Use them as a guide for proper tightening.6. Prime the fuel system. (See next topic).7. Close the access cover.Fuel Priming Pump
1. Unlock and operate the priming pump plunger until a resistance is felt.2. Push the plunger in and tighten by hand.3. Start the engine. If the engine will not start, or once started continues to misfire or smoke, further priming is necessary.4. If
Change Filter
The transmission filter is located on the left side of the machine under the steps. 1. Remove the filter element with a strap-type wrench.2. Clean the filter housing base. Make sure all of the old filter gasket is removed.3. Apply a light coat of oil to the gasket of the new filter.4. Install the new filter by hand. When the gasket contacts the filter base, tighten the filter three-quarter of a turn more.5. Start the engine. Apply the service brake.6. Slowly operate the transmission controls to circulate the transmission oil.7. Move the transmission control lever into NEUTRAL. Engage the parking brake. Inspect for leaks. 8. Maintain the oil level between the marks on the low idle side of the dipstick with the transmission in neutral. Add oil if necessary.9. Stop the engine.Hydraulic Oil System
Change Filter
1. Remove the oil fill cap slowly to relieve the tank pressure before changing the filters.Hydraulic Oil Tank Filter
2. Loosen the filter housing cover retaining bolt. Remove the filter cover.3. Inspect the cover seal. Replace if necessary.4. Remove and discard the two filter elements.5. Remove the screen. Wash screen in clean, nonflammable solvent. Dry the screen.6. Install the screen and two new filter elements.7. Install the cover. 8. Maintain the hydraulic oil level above the ADD COLD mark in the sight gauge.9. Inspect the fill cap gasket. Replace the gasket, if damaged. Install the oil fill cap.Fuel System
Clean and Change Filters
Do not fill fuel filters with fuel before installing them. Contaminated fuel will cause accelerated wear to fuel system parts.
Wash the Primary Filter Element
1. Open the access cover of the machine. 2. Loosen the filter housing retaining bolt (1).3. Remove the housing (2) and element.4. Remove the element from the case.5. Wash the element and housing in clean, nonflammable solvent.6. Dry the element using pressure air.7. Clean the filter case base.8. Inspect the seal. Replace if damaged.9. Insert the clean element.10. Install the element and case into housing.11. Retighten the retaining bolt to a torque of 24 4 N m (18 3 lb ft).12. Close the access cover.Change Secondary Fuel Filter
1. Open the access cover. 2. Remove and discard the filter.3. Clean the filter mounting base. Be sure all of the old seal is removed.4. Coat the seal of a new filter with clean diesel fuel.5. Install the new filter by hand. When the seal contacts the base, tighten three-quarter of a turn more.There are rotation-index marks 90° apart on the filter. Use them as a guide for proper tightening.6. Prime the fuel system. (See next topic).7. Close the access cover.Fuel Priming Pump
1. Unlock and operate the priming pump plunger until a resistance is felt.2. Push the plunger in and tighten by hand.3. Start the engine. If the engine will not start, or once started continues to misfire or smoke, further priming is necessary.4. If
Caterpillar parts catalog:
Parts cable Caterpillar catalog:
3422980
CABLE AS
324D L, 329D, 329D L, 329D LN
324D L, 329D, 329D L, 329D LN
3422839
CABLE AS
320D LRR, 320D RR
320D LRR, 320D RR
3422838
CABLE AS
320D LRR, 320D RR
320D LRR, 320D RR
3422837
CABLE AS
320D LRR, 320D RR
320D LRR, 320D RR
3422915
CABLE AS
320D L, 323D LN, 323D SA
320D L, 323D LN, 323D SA
3422914
CABLE AS
320D L, 323D LN, 323D SA
320D L, 323D LN, 323D SA
3422929
CABLE AS
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3640361
CABLE AS
324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN
3508406
CABLE AS
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
324E, 324E L, 324E LN, 329E, 329E L, 329E LN
3508283
CABLE AS
324E L, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
324E L, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
3508282
CABLE AS
324E L, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
324E L, 329E L, 336E, 336E L, 336E LH, 336E LN, 336F L
3422982
CABLE AS
324D L, 328D LCR, 329D, 329D L, 329D LN, 336D, 336D L, 336D LN, 336D2
324D L, 328D LCR, 329D, 329D L, 329D LN, 336D, 336D L, 336D LN, 336D2