3940961 CABLE AS Caterpillar parts
301.7D, 302.2D, 302.4D
Rating:
Alternative (cross code) number:
CA3940961
394-0961
3940961
CA3940961
394-0961
3940961
Weight: 0.14 pounds 0 kg.
MINI HYD EXCAVATOR,
Information:
Introduction
The procedure that follows must be used for breaking in 20R-0194 Cylinder Pack Assemblies that are installed in the field.Do not perform any procedure outlined in this Special Instruction until you have read and understand the information.Special Assembly Instructions for the 20R-0194 Cylinder Pack Assemblies
Utilizing the Disassembly and Assembly, RENR8628 assemble the 20R-0194 Cylinder Pack Assemblies and use the following steps.
Immediately before assembly, heavily lubricate both the piston pin bores and the piston pin with clean engine oil.
Immediately before assembly, heavily lubricate both the piston rings and the piston skirt with clean engine oil.
Run the following break-in procedure as soon as possible after the assembly has been completed.Break-In Procedure
After the installation of the 20R-0194 Cylinder Pack Assemblies , check all fluid levels.
Start the engine.
Idle the engine with no load for 20 minutes.
Check the engine for leaks.
Increase the engine rpm to half throttle once the coolant temperature begins to move on the temperature gauge.
Run the engine for 10 minutes at half throttle with no load. Check and verify that there is water flow, oil pressure, fuel pressure, and no unusual sounds.
Once the pressures are checked, bring the engine back to idle, and check the marine gear to make sure that the gear engages properly.
Begin a sea trial running the engine at a low load condition until engine temperatures reach operating temperature.
Once the engine has reached operating temperature, begin increasing the engine rpm following the increments in Table 1.
Table 1
Engine Speed (RPM)     Time (mins)    
1000     Until engine reaches operating temperature    
1200     10    
1400     10    
1600     10    
1800     10    
1900     10    
2000     15    
2100     15    
2200     15    
Wide open throttle     10    
Slowly bring the engine speed back to low idle.
The engine is now ready for a full sea trial.
The procedure that follows must be used for breaking in 20R-0194 Cylinder Pack Assemblies that are installed in the field.Do not perform any procedure outlined in this Special Instruction until you have read and understand the information.Special Assembly Instructions for the 20R-0194 Cylinder Pack Assemblies
Utilizing the Disassembly and Assembly, RENR8628 assemble the 20R-0194 Cylinder Pack Assemblies and use the following steps.
Immediately before assembly, heavily lubricate both the piston pin bores and the piston pin with clean engine oil.
Immediately before assembly, heavily lubricate both the piston rings and the piston skirt with clean engine oil.
Run the following break-in procedure as soon as possible after the assembly has been completed.Break-In Procedure
After the installation of the 20R-0194 Cylinder Pack Assemblies , check all fluid levels.
Start the engine.
Idle the engine with no load for 20 minutes.
Check the engine for leaks.
Increase the engine rpm to half throttle once the coolant temperature begins to move on the temperature gauge.
Run the engine for 10 minutes at half throttle with no load. Check and verify that there is water flow, oil pressure, fuel pressure, and no unusual sounds.
Once the pressures are checked, bring the engine back to idle, and check the marine gear to make sure that the gear engages properly.
Begin a sea trial running the engine at a low load condition until engine temperatures reach operating temperature.
Once the engine has reached operating temperature, begin increasing the engine rpm following the increments in Table 1.
Table 1
Engine Speed (RPM)     Time (mins)    
1000     Until engine reaches operating temperature    
1200     10    
1400     10    
1600     10    
1800     10    
1900     10    
2000     15    
2100     15    
2200     15    
Wide open throttle     10    
Slowly bring the engine speed back to low idle.
The engine is now ready for a full sea trial.
Caterpillar parts catalog:
Parts cable Caterpillar catalog:
8I4500
CABLE TIE
2384C, 2484C, 301.7D, 302.2D, 302.4D, 559C, 579C, RT100, RT50
2384C, 2484C, 301.7D, 302.2D, 302.4D, 559C, 579C, RT100, RT50
3941017
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3941045
CABLE AS-BATTERY
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3940977
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3992959
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3882937
CABLE AS
306E
306E
3882936
CABLE AS
306E
306E
3882935
CABLE AS
306E
306E
3886764
CABLE AS
318D2 L
318D2 L
3886768
CABLE AS
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP
3886767
CABLE AS
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP
312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP
4314555
CABLE AS
308E
308E
4306434
CABLE AS
308E
308E
3992959
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3940977
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3941045
CABLE AS-BATTERY
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D
3941017
CABLE AS
301.7D, 302.2D, 302.4D
301.7D, 302.2D, 302.4D