6T1313 CABLE AS Caterpillar parts
936, 936F, G936
Rating:
Alternative (cross code) number:
CA6T1313
6T-1313
6T1313
CA6T1313
6T-1313
6T1313
Weight: 1 pounds 0 kg.
Information:
LENGTH
1720
mm
MINIMUM BEND RADIUS
178
mm
TRAVEL
50.8
mm
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
6T-1313 Cable A (Surplus Open Box) - G&T Engine Parts
G&T Engine Parts Condition: Surplus Open Box || Weight: 1.87 lbs || Dimensions: 10-22.52-22.52 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: Surplus Open Box || Weight: 1.87 lbs || Dimensions: 10-22.52-22.52 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
CTP 6T1313 Cable for Models 936/936F/G936 Caterpillar
CTP For Model 936/936F/G936 Caterpillar || Sold in each || Easy in-and-out fit
CTP For Model 936/936F/G936 Caterpillar || Sold in each || Easy in-and-out fit
Information:
Remove & Install Piston & Connecting Rod Assemblies
Start By:a. remove cylinder head assemblyb. remove oil pan 1. Remove the bolt that holds piston cooling jet (1) in position. Remove the piston cooling jet.2. Check the connecting rods and caps for their identification mark and location. The connecting rod and the rod cap should have the cylinder number etched on the right side as indicated by the arrow. If not marked, etch each unmarked connecting rod/or cap during removal.3. Remove rod cap bolts (2) and the cap from the connecting rod. Remove the lower half of the bearing from the cap. 4. Push piston and connecting rod (4) away from the crankshaft; then remove the upper half of rod bearing (5).5. Remove the piston and connecting rod from the cylinder block.6. Repeat Steps 1 through 5 for the other piston and connecting rod assemblies. The following steps are for the installation of the pistons and connecting rod assemblies.7. Put clean engine oil on the piston rings, piston and in the cylinder bore. 8. Position the piston ring end gaps 120 degrees apart. Install Tool (A) to compress the rings.9. With the number one crankshaft throw at bottom center, install the piston and connecting rod.10. Line up the connecting rod with the crankshaft. Using a soft faced hammer, carefully tap the piston into the cylinder bore until Tooling (A) comes off of the piston.11. Before the connecting rod comes in contact with crankshaft, install the upper half of the rod bearing. Be sure the bearing tab properly engages the with slot in the connecting rod.12. Put clean engine oil on the upper rod bearing surface. Using a soft faced hammer, tap the piston down while guiding the connecting rod onto the crankshaft.13. Position the lower half of the rod bearing in the corresponding numbered rod cap. Be sure the bearing tab engages with the grove in the rod caps.14. Put clean engine oil on the lower rod bearing surface; then install the rod cap. Install the bearing cap on the connecting rod with the number on the bearing (rod) cap on the same side and same number as on the connecting rod.15. Put 2P2506 Thread Lubricant on the threads of rod cap bolts (1) and the seating surfaces of the caps. Install rod cap bolts (1). Tighten them to a torque of 130 7 N m (95 5 lb ft). Mark each bolt head, and then tighten each rod cap bolt an additional 1/6 60 5 degrees ( turn).16. Repeat Steps 7 through 15 for the remainder of the piston and connecting rod assemblies.17. Install piston cooling jets (1).End By:a. install oil panb. install cylinder head assemblyDisassemble & Assemble Piston & Connecting Rod Assemblies
Start By:a. remove piston and connecting rod assemblies 1. Use Tooling (A), and remove piston rings (1) from piston crown (2). 2. Remove plug (3), and remove the piston pin. Separate piston crown (2), piston skirt (4) and connecting rod (5).
The connecting rod must
Start By:a. remove cylinder head assemblyb. remove oil pan 1. Remove the bolt that holds piston cooling jet (1) in position. Remove the piston cooling jet.2. Check the connecting rods and caps for their identification mark and location. The connecting rod and the rod cap should have the cylinder number etched on the right side as indicated by the arrow. If not marked, etch each unmarked connecting rod/or cap during removal.3. Remove rod cap bolts (2) and the cap from the connecting rod. Remove the lower half of the bearing from the cap. 4. Push piston and connecting rod (4) away from the crankshaft; then remove the upper half of rod bearing (5).5. Remove the piston and connecting rod from the cylinder block.6. Repeat Steps 1 through 5 for the other piston and connecting rod assemblies. The following steps are for the installation of the pistons and connecting rod assemblies.7. Put clean engine oil on the piston rings, piston and in the cylinder bore. 8. Position the piston ring end gaps 120 degrees apart. Install Tool (A) to compress the rings.9. With the number one crankshaft throw at bottom center, install the piston and connecting rod.10. Line up the connecting rod with the crankshaft. Using a soft faced hammer, carefully tap the piston into the cylinder bore until Tooling (A) comes off of the piston.11. Before the connecting rod comes in contact with crankshaft, install the upper half of the rod bearing. Be sure the bearing tab properly engages the with slot in the connecting rod.12. Put clean engine oil on the upper rod bearing surface. Using a soft faced hammer, tap the piston down while guiding the connecting rod onto the crankshaft.13. Position the lower half of the rod bearing in the corresponding numbered rod cap. Be sure the bearing tab engages with the grove in the rod caps.14. Put clean engine oil on the lower rod bearing surface; then install the rod cap. Install the bearing cap on the connecting rod with the number on the bearing (rod) cap on the same side and same number as on the connecting rod.15. Put 2P2506 Thread Lubricant on the threads of rod cap bolts (1) and the seating surfaces of the caps. Install rod cap bolts (1). Tighten them to a torque of 130 7 N m (95 5 lb ft). Mark each bolt head, and then tighten each rod cap bolt an additional 1/6 60 5 degrees ( turn).16. Repeat Steps 7 through 15 for the remainder of the piston and connecting rod assemblies.17. Install piston cooling jets (1).End By:a. install oil panb. install cylinder head assemblyDisassemble & Assemble Piston & Connecting Rod Assemblies
Start By:a. remove piston and connecting rod assemblies 1. Use Tooling (A), and remove piston rings (1) from piston crown (2). 2. Remove plug (3), and remove the piston pin. Separate piston crown (2), piston skirt (4) and connecting rod (5).
The connecting rod must
Caterpillar parts catalog:
Parts cable Caterpillar catalog:
8V4320
CABLE AS.
936, 936F, CS-643, G936
936, 936F, CS-643, G936
8V4323
CABLE AS.
936, 936F, CS-643, G936
936, 936F, CS-643, G936
9V2904
CABLE AS.
936, 936F, CS-643, G936
936, 936F, CS-643, G936
6T1314
CABLE AS
936, 936F, G936
936, 936F, G936
8V1620
CABLE AS
936, G936
936, G936
9X0390
CABLE AS
916, 926A, 936, 936F, 966D, G936, IT18B, IT28B
916, 926A, 936, 936F, 966D, G936, IT18B, IT28B
6C4086
CABLE
936, 950F, 950F II, 960F, 966F, 966F II, 966G II, 970F, 972G II, 980C, 980F, 980G, IT28B
936, 950F, 950F II, 960F, 966F, 966F II, 966G II, 970F, 972G II, 980C, 980F, 980G, IT28B
6C4085
CABLE (0.5M)
936, 966F, 966F II, 970F, 980C, 980F, 980G
936, 966F, 966F II, 970F, 980C, 980F, 980G
3E0418
CABLE AS
936F
936F
6C8203
CABLE
936F
936F
9C9743
CABLE AS
936F, 980C, 980F, 980F II, 992C, 992D, D8R II, PM-201, PM-565, PM-565B, RM-350B, SM-350
936F, 980C, 980F, 980F II, 992C, 992D, D8R II, PM-201, PM-565, PM-565B, RM-350B, SM-350
4E3470
CABLE
936F, 950F
936F, 950F
6T1314
CABLE AS
936, 936F, G936
936, 936F, G936
2Y2062
CABLE AS
930, 930R
930, 930R
2Y2063
CABLE AS
930, 930R
930, 930R
5T7804
CABLE AS
615
615
3G2079
CABLE ASSEM.
613B
613B
9V2904
CABLE AS.
936, 936F, CS-643, G936
936, 936F, CS-643, G936
5G3258
CABLE AS
910
910
6W4868
CABLE AS
916, 926, 926A, IT18B, IT28B
916, 926, 926A, IT18B, IT28B
9V7254
CABLE AS
916, 926, IT28
916, 926, IT28
9V6944
CABLE AS
916, 926, IT28
916, 926, IT28
8V7916
CABLE AS
916, 926, 926A, IT18B, IT28, IT28B
916, 926, 926A, IT18B, IT28, IT28B
8V1620
CABLE AS
936, G936
936, G936